MLGC 1 Fine Lock Cylinder with Guide Series MLGC 20, 25, 32, 40 A linear transfer cylinder unit with a built-in locking mechanism and a guide rod integrated in a compact design. CL CL1 MLGC CNG MNB CNA CNS CLS CLQ MLGP RLQ MLU ML1C High level of stopping accuracy D-X Locking method Spring locking Pneumatic locking Spring and pneumatic locking 20Locking in both directions is possible.
The figure a seal vent $MC PneumatICS' unique figure 8 seal incorporales vents that allow pressufized air to flow into an Integrated cavity forcing the seal firmly against the opposite side 01 the piston seal groove creating a much tighter, more positive barrier against leakage.
at a constant or low speed or to effect an intermediate stop, just like a hydraulic unit, while using pneumatic equipment such as a valve.
Consult with P/A in case of 10mm or less stroke. In general, mounting on a small-size actuator may cause hunting. For prevention, a pilot valve with a built-in output restriction is available. The restriction is removable.
I nput dat a occupi es 4 w ords, but uses onl y t he 1st w ord. The pressure i s m oni t ored by b15, b1, b0 dat a. ( b11 b0 cover 100% F.
-1.8WDC WF333O Exhaust Conter NVF343O GNced Center (B) (A) (B) (a) 01 c2 \ t \ T I'f E I J E Z (R2)(PxFl) (R2XPXR1) Prssure Center NVF3530 (B) (A) Spej;ifications -, Flurd-Art f Operatangprssurcrange2Positionsingle2O-12gPSlS(1.5-9kgF) U 2 pooition double-1 5 1 28 PSI (1 9kgf/cm'?
ON = A (A B)/4 A = Max. pressure OFF = B + (A B)/4 B = Min. pressure Perform zero clear operation again after restoring the applied pressure to an atmospheric pressure condition. Do not use the product in a place where static electricity is a problem. Otherwise it can cause failure or malfunction of the system.
Caution Caution indicates a hazard with a low level of risk which, if not avoided, could result in minor or moderate injury. Warning Warning indicates a hazard with a medium level of risk which, if not avoided, could result in death or serious injury. Danger Danger indicates a hazard with a high level of risk which, if not avoided, will result in death or serious injury. Warning 1.
a f orm ul a> Set pressure / F. S. pressure range x 4095 The val ue obt ai ned by t hi s f orm ul a i s convert ed t o a hexadeci m al num ber f or sendi ng. EX. ) To set pressure at 0. 3M Pa by I TV203*( f or 0. 5M Pa t ype) O ut put condi t i on can be m oni t ored by readi ng t he dat a of I area or di agnost i c area.
Check that the above-mentioned preparation work has been performed correctly, and part A shown in the figure is pushed by hand and makes temporary connection. Part A centre is pushed straight in using a suitable tool, such as pliers. Re-use cannot be performed once it connects the connector for sensor connection completely.
This can be prevented by inserting a noise filter, such as a line noise filter and ferrite core, between the switch-mode power supply and the product, or by using a series power supply instead of a switchmode power supply. Function selection mode Key-lock function To set this function, refer to SMC website (URL http://www.smcworld.com) for more detailed information or contact us.
Do not apply a lateral load to the external slider. When a load is mounted directly to the cylinder, variations in the alignment of each shaft center cannot be offset, which results in the generation of a lateral load that can cause malfunction.
N5O-PI 63mm CA1N63.PI 80mm cA1 N80-Pl 100mm CAl Nl OO-PS Supply Pressure G 43-10-01 Signal Pressure G 43-2-01 Consult factory regarding Repair Manual SMC Pneumatics, Inc. 3011 N.
Please consult with SMC for the supply of a pressure gauge with NPT port threads. Note 2) Use caution not to tighten excessively when mounting a pressure gauge, otherwise it will may result in a breakdown. For sealing, use a sealant tape. Flow rate (L/min (ANR)) ARP IR-A Option/Mounting Bolt Assembly IR Model Part no. Dimensions Qty.
with a warning tag. 01 02 03 04 06 10 1/8 1/4 3/8 1/2 3/4 1 Body size 2 3 4 5 1/8 3/8 1/2 1 SMC Interface part is required if attached to a modular FRL.
100mm CAl Nl OO-PS Supply P.essure G 43'10-01 Signal Pressure G 43-2-01 co.sull jactory regarding Repair Manua SMC Pneumatics, Inc. @srrc 3011 N. FRANKLIN ROAD. INDIANAPOLIS, IN 46226 TEL: 317-899-4440 FAX: 317-899'3102 For a branch office near you call: 1800 Sl\,1C-SMC1 (762-7621J July 1998 Specifications subject to change without n
The cylinder should be operated using a connection method which allows for shaft alignment variations and deflection due to the cylinder's own weight. A drawing of a recommended mounting method is shown in Figure 1.
Contact P/A regarding the valves 3 to 5.
18 21,32SA SS5YJ3SY3000-37-80A-2 B SY3000-37-80A-7 A 916 SY3000-37-80A-4 B SY3000-37-80A-5 A 18 SY3000-37-80A-2 B 20,40, 42,43SA SS5YJ5SY3000-37-80A-7 A 912 SY3000-37-80A-4 B SY3000-37-80A-9 A 1316 SY3000-37-80A-7 B SY3000-37-80A-7 A 18 SY3000-37-80A-3 B 21,41SA SS5YJ7SY3000-37-80A-10 A 912 SY3000-37-80A-6 B SY3000-37-80A-12 A 1316 SY3000-37-80A-9 B 1)Ass'y 2)Ass'y