Valve for Water and Chemical Base Fluids (2/3 Port Air Operated Valve) Do not use the valves in an atmosphere having corrosive gases, chemicals, salt water, water, steam, or where there is direct contact with any of these. 2. Do not use in locations subject to vibration or impact. 3. Do not use in locations where radiated heat will be received from nearby heat sources. 4.
Do not apply external force to the coil. Apply a wrench to the exterior surface of the piping joint at the time of tightening. 3. Do not use heat insulators, etc. to keep the temperature at the coil assembly. Do not use a tape heater for freeze prevention except on the piping and body. If may cause the coil to burn. Caution 1.
Note 4) Do not apply rotational torque to the rod end. Note 5) The direction of rod end width across flats (12) differs depending on the products.
Do not apply excessive force or shock to the body or fittings with an impact tool. It can cause damage or air leakage. 100 8 7 to 9 150 1/8 14 12 to 14 200 1/4 17 22 to 24 200 3/8 21 28 to 30 200 1/2 24 Lock Nut Tightening Torque Caution 1. Suitable screw torque for a hexagon lock nut is shown in the table below.
Do not ground it with devices generating strong electromagnetic noise. 3. Do not pull sensor cable strongly. Such action may cause failure. 4. Check wiring Incorrect wiring may cause damage or malfunction of the products. Make sure the wiring is correct before operation. 4. Power supply line Do not mount any switch or relay to power supply line (12 VDC to 24 VDC).
Do not cut the tubing with pliers, nippers, scissors, etc., otherwise the tubing will be deformed and problems may result. (3) When mounting the tube, resin plug or metal rod, do not press the release button. Do not press the release button unnecessarily before mounting tubing, resin plugs and metal rods.
Safety Instructions Warning Do not disassemble, modify (including changing the printed circuit board) or repair. An injury or failure can result. Do not operate or set with wet hands. This may lead to an electric shock. Do not operate the product outside of the specifications. Do not use for flammable or harmful fluids. Fire, malfunction, or damage to the product can result.
state auto switch RS2H 2-wire 12 V Connector RSH 3-wire (NPN) IC circuit 5 V, 12 V Relay, PLC Diagnostic indication (2-color indicator) Yes Yes Yes No No 24 V 3-wire (PNP) 2-wire MIW MIS 12 V Grommet 3-wire (NPN) IC circuit 5 V, 12 V Water resistant (2-color indicator) M9PAV1 M9PA1 3-wire (PNP) 2-wire M9BAV1 M9BA1 IC circuit 12 V 5 V, 12 V H7NF With diagnostic output (2-color indicator
12 12 13 149 159 162 178 11 11 11 12 12 12 12 13 149 159 162 178 125 135 136 151 190 16 16 16 16 12 12 12 13 149 159 162 178 186 201 204 230 205.5 227.5 208.5 235 230.5 255 3.1-30 Fine Lock Cylinder/Double Acting Single Rod Series CLG1 Construction CL MLG CNA CNG With air cushion MNB CNS CLS CB CV/MVG CXW CXS Component Parts Material Note Description Material Note Description Rolled steel
Do not use the product in an environment where corrosive gases or fluids could be splashed. Otherwise damage to the product and malfunction can result. Do not use in an area where surges are generated.
The cartridge assembly cannot be inserted while the locking knob is in the LOCK position, attempting to do so may cause damage. Do not directly touch the emitters with your finger or tools. This may result in injury.
Do not use the product in an area where dust, powder 2. Do not operate the product beyond the specifications. dust, water, chemicals or oil is in the air. It will cause failure or malfunction. Otherwise, a fire, malfunction or actuator damage can result. Please check the specifications before use. 11. Do not use the product in an area where a magnetic 3.
Safety Instructions Warning Do not disassemble, modify (including changing the printed circuit board) or repair. An injury or failure can result. Do not operate the product outside of the specifications. Do not use for flammable or harmful fluids. Fire, malfunction, or damage to the product can result. Verify the specifications before use.
PLC Fieldbus network Gateway (GW) unit Serial communication RS485 Up to 12 controllers are connectable.
Metric size 3.2 4 6 8 10 3.2 4 6 8 10 6 8 10 12 10 12 16 Tubing O.D.
Safety Instructions Warning Do not disassemble, modify (including changing the printed circuit board) or repair. An injury or failure can result. Do not operate the product outside of the specifications. Do not use for flammable or harmful fluids. Fire, malfunction, or damage to the product can result. Verify the specifications before use.
Do not pull sensor cable strongly. Such action may cause failure. 4. Water shall be kept away from the sensor unit to avoid failure. (IP65 Protection) 5. Power supply line Do not mount any switch or relay to power supply line (12 VDC to 24 VDC). Measurement Caution SMC products are not intended for use as instruments for legal metrology.
Do not apply excessive force or shock to the body or fittings with an impact tool. It can cause damage or air leakage. 100 8 7 to 9 150 1/8 14 12 to 14 200 1/4 17 22 to 24 200 3/8 21 28 to 30 200 1/2 24 Lock Nut Tightening Torque Caution 1. Suitable screw torque for a hexagon lock nut is shown in the table below.
Do not use in an atmosphere where corrosive gases, chemicals, sea water, water, or water vapor is present. Do not use in cases where there is direct contact with any of the above. 2. Do not use in an explosive environment. 3. Do not use in a place subject to heavy vibration and/or impact. 4. The valve should not be exposed to prolonged sunlight. Use a protective cover if necessary. 5.
Do not use in an atmosphere where corrosive gases, chemicals, sea water, water, or water vapor is present. Do not use in cases where there is direct contact with any of the above. 2. Do not use in an explosive environment. 3. Do not use in a place subject to heavy vibration and/or impact. 4. The valve should not be exposed to prolonged sunlight. Use a protective cover if necessary. 5.