NVZ1000//3000/5000 4,5 Port Solenoid Valve/Rubber Seal Type Whn uslng a Nyz34oo wlth a manilold, us a EXH relocation spacerass'y because lhe erhaual ot other golenoid valves may cause actuator malfunction Plass otder the aDroDriat valves and/or blanking plate ass'y with manitold base.
If tightened too much, thread portion may be damaged and gasket may be deformed. This will cause air leakage. On the contrary, if tightening is not sufficient, thread may loosen causing air leakage. 1 2 2 1 4 93 Series KF Insert Fittings Tube Insert Suitable for use with nylon, soft nylon and urethane. Large retaining force.
Since air may remain inside actuators, piping and manifolds, confirm that the air is completely exhausted before beginning work. 2. When disassembly and assembly are performed, air leakage may result if connections between blocks and tightening of the end block's holding screw, is inadequate.
Brown [Red] When two switches are connected in series, a load may malfunction because the load voltage will decline when in the ON state. The indicator lights will light up if both of the switches are in the ON state.
Otherwise, the contact life may be shortened. (Due to permanent energizing conditions.)
If exceeding that value, fitting may damaged and tubing may burst. 2 The value of the max. operating pressure is at a temperature of 20C. Refer to the burst pressure characteristics curve for other temperatures. Avoid abnormal temperature rises which may burst the tubing. 3 The values of the min. bending radius is at a temperature of 20C.
The product specified here may become unsafe if handled incorrectly. The assembly, operation and maintenance of machines or equipment including our products must be performed by an operator who is appropriately trained and experienced. 3.
The auto switch may be damaged if a screw other than the one supplied is used.
This may cause deformation of the non-rotating guide, abnormal responses of the auto switch, play in the internal guide or an increase in the sliding resistance.
It may cause human injury and/or an accident. 786 AFJ Series Specific Product Precautions 2 Be sure to read this before handling the products. Refer to back page 50 for Safety Instructions. Piping Mounting / Adjustment Caution Caution SP 3. When piping is being installed, connect IN for work side and OUT for ejector. Incorrect connections may cause malfunction. 2.
When the set pressure is 0.15 MPa or less, the valve q may not open due to the valve spring w force.
It may not be applicable when a seal material different from the current one has been chosen.
Due to the different materials used, changing only the seal may prove inadequate.
If the normally open (N.O.) auto-drain is used on AFF2B to AFF75B or AM150 to 850, air may ceaselessly blow out of the drainage discharge area in cases where an air compressor with a small air discharge volume is used since it is designed so that the valve will not close unless the air pressure is 0.15 MPa or higher.
There may be the case it will vary substantially depending on an ambient environment. CUJ CU CQS Precautions CQM Be sure to read before handling. For Safety Instructions and Actuator Precautions refer to pages 7-13-3 to 7-13-6.
(variations on the order of 30%) Large variations may occur depending on the surrounding environment.
Any changes made during operation are ignored and may lead to problems during the next power-up sequence. 2 Outline with Dimensions US1 Indicator Specification Mounting After maintenance is complete, perform appropriate functional inspections. Stop operation if the equipment does not function properly. Safety cannot be assured in the case of unexpected malfunction.
Otherwise, malfunction may result due to noise. Ensure that the FG terminal is connected to ground when using a commercially available switch-mode power supply. Do not operate in an atmosphere containing flammable or explosive gases. Fire or an explosion can result. This product is not designed to be explosion proof.
If the tightening torque is insufficient, the fittings may become loose. When connecting piping to the product, a spanner should be used on the metal piping attachment only. Using a spanner on other parts may damage the product. Avoid any sealing tape from entering inside the piping. Ensure that there is no leakage from loose piping.
If the tightening torque is insufficient, the fittings may become loose. When connecting the piping, hold the specified part of the body with a spanner. Using a spanner on other parts may damage the product. Avoid any sealing tape from entering inside the piping. Ensure that there is no leakage from loose piping. Avoid sudden changes in the piping size on the IN side of the sensor.