08-ca2kw-e A rod seal may allow air leakage depending on the position where it is installed. Therefore, please consult with SMC when a rod seal is to be replaced. 2. Do not replace the non-rotating guide. Since the non-rotating guide is press fitted, the entire cover assembly needs be replaced instead of a single part. 38
Please note that disassembly by the spring reaction force, because it may cover will pop up. When disassembling cylinders, grip the double flat part of either the head cover or the rod cover with a vise and loosen the other side with a wrench or a monkey wrench, etc., and then remove the cover. When re-tightening, tighten approximately 2 degrees more than the original position. 20 A
If the differential pressure is small, the internal part is worn out due to the structure of this product and the bleed amount from the exhaust port increases, which may affect the characteristics.
If the differential pressure is small, the internal part is worn out due to the structure of this product and the bleed amount from the exhaust port increases, which may affect the characteristics.
If connected, the metal rod cannot be retained by the chuck of the One-touch fitting and products with metal rods may project during pressurization, causing serious personal injury or accident. For details about One-touch fittings that can connect products with metal rods, contact SMC.
This software cannot be used with Windows 3.1. 80 9 Controller Setup Software Series LC1 Windows/LC1-1-W2 (English) Screen example The contents of this software and the registered product specifications may change without prior notice. Duplicating, copying or reproducing of this software, in whole or in part, is prohibited without prior consent from SMC.
Also, if tubes are attached after metal rods or pipes have been attached, the tubes will not hold and may come loose. Disassembly (1) Loosen clamp ring A and disassemble the connector into the plug case and socket case. KK130 DM DM Clamp ring KDM Installation and Removal of One-touch Mini Fittings KB Caution KR Installation of tubing 1.
It may change substantially depending on the ambient environment. Auto switch (Sensor section) Auto switch (Amplifier section) Safety Instructions Be sure to read the Handling Precautions for SMC Products (M-E03-3) and Operation Manual before use.
Residual Pressure Relief Valve How To Order Series VHS 20 to 40 VHS 30 N 03 Z X513 Residual Pressure Relief Valve With External Epoxy Coating Stainless Fasteners Body Size Symbol 20 30 40 Applicable Model AC21 AC31 AC41 Name Plate in imperial Units (psi, F) Thread Type Body Size Port Size N NPT Port Size Symbol 20 30 40 1/4 3/8 1/2 02 03 04 Note: Other sizes, thread forms, options, etc. may
Sending this email per your rquest so you may contact me with sketch of the pneumatic circuit using the F-4103 unit made by Airtrol. lf you remember my application was usin the two opposing air cylinders to achieve that "human" touch and balancing that using the bias in this design. thanks, Darryl Knight -/ l,{(q 9t2t2005 iu*,{rtL 5%s
Caution The bronze element may be discolored by the moisture included in the atmosphere, but this does not affect the characteristics.
(Reset type) Perform element replacement when the red ring floats up and covers the entire view port. 0.05 0.04 0.03 04 0.02 Pressure drop (MPa) 03 w Operation The hydraulic fluid used becomes high viscosity when the temperature is low during the winter, etc., and the differential pressure indicator or the switch may activate.
-04 FH99-FL006-N V FH99-FL005-N V FH990-06 FH99-FL009-N V FH99-FL007-N V FH990-08 FH99-FL009-N V FH99-FL008-N V FH990-10 One set each of companion flange, seal, hexagon socket head cap screws FH99-FL011-N V FH99-FL010-N V w Operation The hydraulic fluid used becomes high viscosity when the temperature is low during the winter, etc., and the differential pressure indicator or the switch may
N.C. and N.O. common w Operation The hydraulic fluid used becomes high viscosity when the temperature is low during the winter, etc., and the differential pressure indicator or the switch may activate. If this occurs, wait until the oil temperature rises by a warm-up operation, then check if this is caused by clogging.
For maintenance, make sure to provide sufficient space above the filter for removing the element. w Operation The hydraulic fluid used becomes high viscosity when the temperature is low during the winter, etc., and the differential pressure indicator or the switch may activate.
: Left to right Flow direction: Right to left + y Nil Y Knob f Downward Upward + Nil Z Note 5) Pressure unit g Name plate and pressure gauge in imperial units: MPa Name plate: psi, Pressure gauge: Both MPa and psi Note 6) Note 6) Note 6) Note 6) Note 6) Note 6) Note 1) When using a non-relieving type with a backflow function, if the inlet pressure is increased slowly, the inlet pressure may
Furthermore, abnormal temperature rises caused by adiabatic compression may result in the burst of the tube. 3.The value of the minimum bending radius is measured at the temperature of 20C as shown in the figure on the right. Bend the tube into U-form at a temperature of 20C. Fix one end and close loop gradually. Measure 2R when the tube breaks or is crushed. Fixed end 1232
(Coil temperature: 20C, pressure: 0.5 MPa, at rated voltage, with light and surge suppressor, value at operation excluding restart period) The period immediately after a restart may be delayed for about 1 msec depending on operating conditions. Note 2) Use dry air to prevent condensation when operating at low temperatures.
right Flow direction: Right to left + Nil Z Note 8) Pressure unit g Name plate, caution plate for bowl, and pressure gauge in imperial units: MPa Name plate: psi, Caution plate for bowl: psi, F , Pressure gauge: Both MPa and psi Note 9) Note 9) Note 9) Note 9) Note 1) When using a non-relieving type with a backflow function, if the inlet pressure is increased slowly, the inlet pressure may
Residual Pressure Relief Valve How To Order Series VHS 20 to 40 VHS 30 N 03 Z X513 Residual Pressure Relief Valve With External Epoxy Coating Stainless Fasteners Body Size Symbol 20 30 40 Applicable Model AC21 AC31 AC41 Name Plate in imperial Units (psi, F) Thread Type Body Size Port Size N NPT Port Size Symbol 20 30 40 1/4 3/8 1/2 02 03 04 Note: Other sizes, thread forms, options, etc. may