Short Stroke Electric Actuator Series LX (B contact) Operating temperature range Work load Speed Positioning repeatability C kg Performance to 100 Note 2) mm/s 0.05 mm 5 phase stepper motor (without brake) Ball screw 8mm, 6mm lead Direct acting guide Motor Lead screw Guide Main parts Note 1) When mounting a work piece to the actuator's end plate, its weight should be within the value inside ( ).
Not mounted Sensor Part name Type D Sensor 1 Rotary sector type Cable Part name Type C Cable S For sensor 3m P For power supply 3m Bracket Type Part name E For body end B Bracket M For body middle part S For sensor Electrode needle cartridge Type Part name N Electrode Needle cart. T Tungsten 3. Specifications 3-1.
Leakage voltage Take note that the leakage voltage will increase when a resistor is used in parallel with a switching element or when a C-R circuit (surge voltage suppressor) is used for protecting a switching device because of the leakage voltage passing through the C-R circuit. The suppressor residual leakage voltage should be as follows. Keep it at 2% or less of the rated voltage.
For connector with mark C, one CEP1 without connector can be directly connected to terminal block of counter. piece of cylinder side connector (male) is enclosed.
C: Modified errors in text. D: Contents revised in several places. [July 2018] E: Contents are added.
(C) Fig. (B) Fig. (A) Set needle Piston valve Switching valve Switching valve Switching valve Switching valve Cylinder Cylinder Cylinder Cylinder Check valve (Stroke end) Fig. (C) Set pressure for piston valve > Pressure in the cylinder Set pressure for piston valve < Pressure in the cylinder (Stroke end) The air that has been supplied by the switching valve closes the check valve.
Printed in Japan. 1st printing February, 2002 D-DAD P-80 (D) This catalog is printed on recycled paper with concern for the global environment.
M5 thread OUT IN Symbol Plate PEEK PEEK PEEK Diaphragm EPDM FKM Kalrez A B C 11R 2 N.C. (Symbol 1) IN (Symbol 2) OUT Option Nil Nil Bracket Manual override Bracket, Manual override 1 2 3 12R N.O.
Displays in turn Normal output Bracket A M3x5 L M3x5 L Bracket B M3x5 L Bracket C Reversed output : The bracket A/B/C can be mounted in 4 ways. Safety Instructions 3. Press the or button to change the set value. The button is to increase and the button is to decrease. Press the button once to increase by one digit, and press it continuously to keep increasing the set value.
ID-200Z ID-300Z ID-400Z ID-600Z 15.4 18.7 40.8 55.1 A B C inch mm inch mm inch mm 120 120 170 170 Operation Principles Provides dry air at dew point as low as 58F (50C).
Use the appropriate pliers (C-type snap ring mounting tool) for installation and removal of the snap ring. 2. Take precautions even when using the appropriate pliers (C-type snap ring mounting tool). The snap ring may slip off the end of the pliers (C-type snap ring mounting tool) and spring out, causing bodily injury or damage to nearby equipment.
Note) Consult with P/A when operating with a stroke below those shown above.
(from 2 to 3 and from 4 to 5) C(Sonic conductance) and b(critical pressure ratio) are subject to ISO 6358/JIS B 8390. Cv (Flow coefficient) is subject to ANSI/CNFPA) T3.21.3.
ZSE10 compact, digital pressure switch for vacuum/compound pressure has been reduced in height by approximately 50% when compared to the ZSE30A. Up to 10 slave sensors can be set at once using the copy settings function. Options include direct mount, panel mount or DIN rail mount, and a choice of 2 piping directions., Low Profile Dig Pres Switch, VACUUM SWITCH, ZSE50-80, M46, 23 lb
Cylinder Port: NPT, Arm Opening Angle: 30°, Arm Position: D (Both Sides), Switch Type: T (Turk PNP), R Arm Mtg Position: C (Mounting Position C), R Arm Style: A029 (25mm Offset Machined ref NAAMS ACA131M), L Arm Mtg Position: C (Mounting Position C), L Arm Style: A029 (25mm Offset Machined ref NAAMS ACA131M), Painted Arm: P (Paint)
Cylinder Port: NPT, Arm Opening Angle: 45°, Arm Position: D (Both Sides), Switch Type: -X167USA (Turk NPN AC), R Arm Mtg Position: C (Mounting Position C), R Arm Style: A011 (Straight Machined ref NAAMS ACA111M), L Arm Mtg Position: C (Mounting Position C), L Arm Style: A012 (Straight Machined ref NAAMS ACA112M), Painted Arm: P (Paint)
Cylinder Port: NPT, Arm Opening Angle: 45°, Arm Position: D (Both Sides), Switch Type: -X167USA (Turk NPN AC), R Arm Mtg Position: C (Mounting Position C), R Arm Style: A012 (Straight Machined ref NAAMS ACA112M), L Arm Mtg Position: C (Mounting Position C), L Arm Style: A011 (Straight Machined ref NAAMS ACA111M), Painted Arm: P (Paint)
Cylinder Port: NPT, Arm Opening Angle: 45°, Arm Position: D (Both Sides), Switch Type: -X167USA (Turk NPN AC), R Arm Mtg Position: C (Mounting Position C), R Arm Style: A012 (Straight Machined ref NAAMS ACA112M), L Arm Mtg Position: C (Mounting Position C), L Arm Style: A012 (Straight Machined ref NAAMS ACA112M), Painted Arm: P (Paint)
Cylinder Port: NPT, Arm Opening Angle: 75°, Arm Position: D (Both Sides), Switch Type: T (Turk PNP), R Arm Mtg Position: C (Mounting Position C), R Arm Style: A012 (Straight Machined ref NAAMS ACA112M), L Arm Mtg Position: C (Mounting Position C), L Arm Style: A018 (Straight Machined ref NAAMS ACA118M), Painted Arm: P (Paint)
Cylinder Port: NPT, Arm Opening Angle: 75°, Arm Position: D (Both Sides), Switch Type: T (Turk PNP), R Arm Mtg Position: C (Mounting Position C), R Arm Style: A018 (Straight Machined ref NAAMS ACA118M), L Arm Mtg Position: C (Mounting Position C), L Arm Style: A012 (Straight Machined ref NAAMS ACA112M), Painted Arm: P (Paint)