LZ-OM004xx It may cause fire, Do not overhaul or modify parts (incl. circuit board).
Countermeasures for static electricity Since static electricity may be generated depending on the fluid being used, implement suitable countermeasures.
Quantification of cycle time improvements For reduction of numerical management/adjustment labor when starting up equipment For reduction of numerical confirmation/inspection labor during periodic maintenance Example of cycle time measurement Caution The measurement may not be performed with an air gripper or rotary actuator, or the measurement deviation may increase.
Breakage may occur. Main screen [ ] [ ] Range in which [ON/OFF] is displayed in the main screen Switch output is automatically turned OFF. Switch output is automatically turned OFF. Switch output is normally output.
In such cases, the valve will not switch completely and the cylinder may malfunction.
The riser piping at the outlet of the filter may also cause backflow. So, take appropriate measures shown above. 3. Firmly fix the bottom to the ground using foundation bolts, etc. 4. Connect the valves or fittings suited to the operating conditions by checking the size of each connection port.
When the set pressure is 0.15 MPa or less, the valve q may not open due to the valve spring w force.
Adjust the operating pressure of the liquid collector using the stop valve. 1.The drive pressure, fluid, fluid viscosity, collection tube length, and/or pump head may affect the collected flow rate, and the liquid may not be collected or backflow to the strainer side depending on the conditions.
The surface may become hot depending on the energization state; therefore, do not touch the solenoid valves. When the manual override is operated, connected equipment will be actuated. Confirm safety before operating.
Scratches or gouges in the piston rod may lead to damaged bearings and seals, and causes malfunction or air leakage. 3. A bumper at the end of the bumper bolt is replaceable. In case a missing bumper, or a bumper has a permanent setting, use the following part numbers for ordering. 3. Secure the plate before mounting the load.
The surface may become hot depending on the energization state; therefore, do not touch the solenoid valves. When the manual override is operated, connected equipment will be actuated. Confirm safety before operating. Non-locking push type [Standard] Press in the direction of the arrow.
It may vary depending on connections.
Note 2) When holding a workpiece close at the end of open/close stroke of fingers, detecting performance of the combinations listed in the above table may be limited, depending on the hysteresis of an auto switch, etc. 12-12-10 12-12-11
There may be the case it will vary substantially depending on an ambient environment. 8 9 9 9 4 4.5 5 4 35 40 45 40 Auto Switch Mounting Bracket Part No.
Do not disassemble the product because it may damage the air cushion mechanism.
Lack of contact protection may cause a reduction in switch service life. 2. D-P74 auto switch is polarized when DC24V is used: white lead wire is positive and black lead wire is negative.
When mounted vertically, use caution since the arm may interfere with the equipment, jig or mounting bolt. Please follow the Recommended arm installation instructions when setting the arm in a vertical clamping position. When installing the arm backwards, use caution as the arm may interfere with the equipment, jig or mounting bolt.
There may be the case it will vary substantially depending on an ambient environment. 8 9 9 9 4 4.5 5 4 35 40 45 40 Auto Switch Mounting Bracket Part No.
Auto switches of models A9V and M9V may not be mounted on the side with ports due to the cylinder stroke or the size of the fittings. Bore size 12 16 20 25 12 mm 16 mm 20 mm 25 mm Cylinder stroke (mm) Refer to "Standard Stroke" on page 10-4-3.
Load mounting without securing the plate may cause galling of the piston rod, leading to particle generation. Piping CXS32 CXS20/25 Model CXS6/10/15 Caution CXS32-34A 28751 CXS20-34A 28749 Part number CXS10-34A 28747 1. Plug the appropriate supply port(s) according to the operating conditions.