CJ2X/CUX/CQSX/CQ2X/CM2X Grease pack GR-L-005 (5 g) GR-L-010 (10 g) GR-L-150 (150 g) RB Operating Precautions J Warning 1. It might not be able to control CUX10 by meter-out at a low speed operation. DCaution -X 1.
Grease pack GR-L-005 (5 g) GR-L-010 (10 g) GR-L-150 (150 g) RB Operating Precautions J Warning 1. It might not be able to control CUX10 by meter-out at a low speed operation. DCaution -X 1.
m l m m m L L t t t t B1 H1 Dd9 Applicable bore size (mm) L L Dd9 d l l d m t Applicable bore size (mm) Part no.
The spacing (L) of the intermediate supports must be no more than the values shown in the following graph. 25 LEMH32 20 Load mass m [kg] LEF m 15 LEJ LEMH25 L 10 LEL 5 LEM LEM m 0 0 200 400 600 800 1000 1200 1400 L LEY Support spacing L [mm] m LES 25 LEPY LEPS L L LEMHT32 20 Load mass m [kg] LER 15 LEH LEMHT25 m m 10 LEY -X5 L 5 11LEFS 0 0 200 400 600 800 1000 1200 1400 11LEJS Square nuts
m l m m m L L t t t t B1 H1 (mm) (mm) (mm) Dd9 Applicable bore size (mm) L L Dd9 d l l d m t Snap ring Snap ring t m Part No.
L plug connector (L) (Made to order) 100V AC 200V AC 110V AC 220V AC 0.6 0.7 M plug connector (M) (A) 2 1 (P) 3 (R) M plug connector (M) N.O.
auto switch DM2 C H L 40 F A J H7BW 150 Number of auto switches Bore size Rod boot 2 pcs. 1 pc. n pcs.
Required flow rate Recommended flow rate = Number of elements FGE 400 L/min or less 800 L/min or less 1200 L/min or less FGG [Recommended flow rate per one element] 400 L/min (Pressure drop 7 kPa to 8 kPa) When viscosity rate is equivalent to water.
m l m m m L L t t t t B1 H1 (mm) (mm) (mm) Dd9 Applicable bore size (mm) L L Dd9 d l l d m t Snap ring Snap ring t m Part No.
Male elbow: KRL Inch e l b a c i l p p A . D .
N x P (52) 28 20 U N (M6 x 1) C (5.1) 1 0.2 5 T-slot A 36: T-slot pitch 39 36 28 Body mounting reference plane 4H9 +0.030 0 6.5 27.5 C Work piece mounting reference plane Refer to Cross section C-C. depth 4 4H9 +0.030 0 L-M6 x 1 Depth 4 T-slot B (mm) Cross section C-C 10 4 5.5 D 4 4 4 4 6 E 6 6 8 8 8 F 107 112 122 132 112 G 55 65 75 85 65 I 1 1 1 1 2 J 65 75 65 70 75 K 2 2 3 3 3 L 6 6 6 6
Temperature specifications Symbol Nil M9N (L) M9P (L) M9B (L) A90 (L) A93 (L) M9// Symbol Nil H0 Temperature range 5 to 60C 5 to 150C Without auto switch (without built-in magnet) Remarks Auto switch D-M9N (L) D-M9P (L) D-M9B (L) D-A90 (L) D-A93 (L) Solid state switch 6. No. of auto switches/Detecting position Quantity Without auto switch 2 pcs. 1 pc. 1 pc.
Supply pressure: 0.1 MPa (7 L/min (ANR) per nozzle) Installation height of sensor: 10 mm 3 Electrostatic potential [kV] 20 With sensor Ionizer 2 Without sensor Without sensor Discharge time [s] 15 1 With sensor L 0 10 1 Workpiece Without sensor 5 2 With sensor 3 0 500 1000 1500 2000 Installation distance L [mm] 1 2 3 4 Time [s] Run mode after static neutralization (electrostatic potential
Operating air pressure Air discharge if no drainage 6 l (ANR) each time 0.3MPa Model Air flow capacity (l/min (ANR)) 50/60Hz IDF2D 120 140 IDF1D 85 100 IDF4D 215 250 IDF3D 180 210 10 l (ANR each time 0.5MPa 50Hz 60Hz 14 l (ANR) each time 0.7MPa Operation cycle: 1 cycle/min. Operation time: 2 sec./min. IDF220B to 370B standard.
The length of the clamp arm L should be the length given below or less.
L1 A B L L1 A B L L1 17 17 19.5 22.5 A 12 16 20 25 14 15.5 18.5 22.5 3.5 3.5 4.5 5 22 22 29.5 32.5 31 31 42 45.5 26 26 32 35.5 14 15.5 18.5 22.5 24 25.5 28.5 32.5 5 to 30 5 to 30 5 to 50 5 to 50 3.5 3.5 4.5 5 13.5 13.5 14.5 15 35 to 100 35 to 100 75 to 200 75 to 300 51 51 63.5 67 32 32 41 44 Bore size (mm) Rod end male thread FD FT FV FX FZ 12 16 20 25 4.5 4.5 6.6 6.6 5.5 5.5 8 8 25 30 39
Body Through-hole l l Maximum tightening torque (Nm) Max. screw-in l (mm) Bolt Model 2. If intermediate stops by external stopper is done, avoid ejection. If lurching occurs damage can result.
Iron (Fe) [mg/L] 1.0 or less Copper (Cu) [mg/L] 0.3 or less Sulfide ion (S2) [mg/L] Should not be detected. Ammonium ion (NH4+) [mg/L] 1.0 or less Residual chlorine (Cl) [mg/L] 0.3 or less Free carbon (CO2) [mg/L] 4.0 or less Refrigerant R407C (HFC) IDU E Reference item *1 In the case of [Mcm], it will be 0.00125 to 0.01.