LFE-OMZ0013 Temperature characteristics 0.5F.S.(25 oC reference) Accumulated flow range*1 9.9 L 9 L By 0.1L By 1L Switch output NPN or PNP open collector output Maximum load current 80 mA Maximum applied voltage 28 VDC Internal voltage drop NPN: 1 V max. (at 80 mA load current) PNP: 1.5 V max.
For details, refer to the [5.19 Communication function]. *2 When using with optional accessories, depending on the accessory, the allowable current of 24 VDC devices will be reduced. Refer to the operation manual of the optional accessories for details.
For details, refer to the [5.19 Communication function]. *2 When using with optional accessories, depending on the accessory, the allowable current of 24 VDC devices will be reduced. Refer to the operation manual of the optional accessories for details.
For details, refer to the [5.19 Communication function]. *2 When using with optional accessories, depending on the accessory, the allowable current of 24 VDC devices will be reduced. Refer to the operation manual of the optional accessories for details.
For details, refer to the [5.19 Communication function]. *2 When using with optional accessories, depending on the accessory, the allowable current of 24 VDC devices will be reduced. Refer to the operation manual of the optional accessories for details.
For details, refer to the [5.19 Communication function]. *2 When using with optional accessories, depending on the accessory, the allowable current of 24 VDC devices will be reduced. Refer to the operation manual of the optional accessories for details.
Prepare the switch (power supply voltage: 24 VDC, contact capacity: 35 mA or more, minimum load current: 5mA) and suitable connector cable. HRS Series 3.3 Installation 3-21 DOC1001322 Chapter 3 Transport and Setting Up 2. Wire the contact input / output signal connector as follows and connect it to this product.
Prepare the switch (power supply voltage: 24 VDC, contact capacity: 35 mA or more, minimum load current: 5mA) and suitable connector cable. HRL Series 3.3 Installation 3-21 HRX-OM-W060 Chapter 3 Transport and Setting Up 2. Wire the contact input / output signal connector as follows and connect it to this product.
Prepare the switch (power supply voltage: 24 VDC, contact capacity: 35 mA or more, minimum load current: 5mA) and suitable connector cable. HRL Series 3.3 Installation 3-21 HRX-OM-Y098 Chapter 3 Transport and Setting Up 2. Wire the contact input / output signal connector as follows and connect it to this product.
Prepare the switch (power supply voltage: 24 VDC, contact capacity: 35 mA or more, minimum load current: 5mA) and suitable connector cable. 3.3 Installation HRL Series 3-22 HRX-OM-X037 Chapter 3 Transport and Setting Up 2. Wire the contact input / output signal connector as follows and connect it to this product.
For details, refer to the [2.4 Setting and checking] *2 When using with optional accessories, depending on the accessory, the allowable current of 24 VDC devices will be reduced. Refer to the operation manual of the optional accessories for details.
Model Thread size Tightening torque SX3000 M2 0.17 Nm SX5000 M3 0.8 Nm SX7000 M4 1.4 Nm 11 SX3000-OMM0002-B -12-SX3000-OMM0002-B -13SX3000-OMM0002-B TROUBLESHOOTING Should any trouble be found during operation, trace the source of the trouble in the following order and take corrective action.
Connection of fittings When screwing fittings into valves, tighten as follows. (1) Follow the procedures below when installing an SMC fitting, etc. 1) M3 types After tightening the fitting by hand, use a wrench to tighten the fitting an additional approximately 1/4 turn.
Additionally, note that the 12 VDC relay does not apply to the auto switch. 11. Pay attention to leakage current. <2-wire type> Current (leakage current) flows to the load to operate the internal circuit even when in the OFF state.
Actuation: 2 (Normally Open), Piping: 4 (Standard, Base Mounted), Voltage: 5 (24 VDC), Electrical Entry: M (M Plug Connector, w/Lead Wire Length 300 mm), Light/Surge Voltage Suppressor: Z (w/Light/Surge Voltage Suppressor, Manual Override: Non-locking Push Type, Port Size: M3 (Standard, Body Ported; Standard Base Mounted, w/Sub Plate)
Actuation: 1 (Normally Closed), Piping: 4 (Standard, Base Mounted), Voltage: S (5 VDC), Electrical Entry: M (M Plug Connector, w/Lead Wire Length 300 mm), Light/Surge Voltage Suppressor: Z (w/Light/Surge Voltage Suppressor, Manual Override: Non-locking Push Type, Port Size: M3 (Standard, Body Ported; Standard Base Mounted, w/Sub Plate)
Actuation: 1 (Normally Closed), Piping: 4 (Standard, Base Mounted), Voltage: 5 (24 VDC), Electrical Entry: M (M Plug Connector, w/Lead Wire Length 300 mm), Light/Surge Voltage Suppressor: Z (w/Light/Surge Voltage Suppressor, Manual Override: Non-locking Push Type, Port Size: M3 (Standard, Body Ported; Standard Base Mounted, w/Sub Plate)
Actuation: 1 (Normally Closed), Piping: 4 (Standard, Base Mounted), Voltage: S (5 VDC), Electrical Entry: M (M Plug Connector, w/Lead Wire Length 300 mm), Light/Surge Voltage Suppressor: w/o Light/Surge Suppressor, Manual Override: Non-locking Push Type, Port Size: M3 (Standard, Body Ported; Standard Base Mounted, w/Sub Plate)
Actuation: 1 (Normally Closed), Piping: 4 (Standard, Base Mounted), Voltage: 5 (24 VDC), Electrical Entry: L (L Plug Connector, w/Lead Wire Length 300 mm), Light/Surge Voltage Suppressor: Z (w/Light/Surge Voltage Suppressor, Manual Override: Non-locking Push Type, Port Size: M3 (Standard, Body Ported; Standard Base Mounted, w/Sub Plate)
Actuation: 2 (Normally Open), Piping: 3 (Standard, Body Ported), Voltage: 5 (24 VDC), Electrical Entry: L (L Plug Connector, w/Lead Wire Length 300 mm), Light/Surge Voltage Suppressor: Z (w/Light/Surge Voltage Suppressor, Manual Override: Non-locking Push Type, Port Size: M3 (Standard, Body Ported; Standard Base Mounted, w/Sub Plate)