ASx-OMX0006 56 or more 44 or more 26 or more 20 or more 3/16 67 or more 52 or more 38 or more 24 or more 6 84 or more 66 or more 39 or more 30 or more 1/4 89 or more 70 or more 57 or more 32 or more 3)Grasp the tubing, and slowly push it straight into the One-touch fitting until it comes to a stop. 4)Pull the tubing back gently to make sure it has a positive seal.
The number of available node is up to 32 stations per segment (without repeater) or 126 stations (with repeater). NOTE 1. Be sure to turn off the power before setting the switches. 2. Be sure to set these switches before use. The factory default settings are all "OFF" or "0". 3.
High pressure switch IDU Series 5-2 Cause and countermeasure of errors 5 3 IDX-OM-W028 Air Dryer 6 References 6 References 6-1 Specifications IDU22E~75E-23 Model Specification IDU22E-23 IDU37E-23 IDU55E-23 IDU75E-23 Air Flow Rate m3/min (ANR)(Note 1) 50Hz 3.9 5.7 8.4 11.0 Rated Condition Operating Pressure MPa 0.7 Inlet Air Temperature 55 Ambient Temperature 32 Pressurized Dew Point 10
IDU Series 9-1 Safety instructions 91 IDX-OM-W013 Air Dryer 9 Specification for Option L 9-3 Installation of heavy duty auto drain 1) Hold the hexagon-head part (width across flats: 32) at port Rc1/2 of the air dryer with spanner. Then install nipple, ball valve (width across flats: 25). Note 1) Put up the seal tape or the sealant to the nipple.
Specifications 32 Dimensions 34 -1No.SFOD-OMO0004-B Safety Instructions These safety instructions are intended to prevent hazardous situations and/or equipment damage.
If max. number of connected slave is 32(IN16/OUT16), the setting range is 0 to 15. For master unit CQM1 The number of channel occupied by PLC of master unit and the number of point occupied by one node address are related additionally.
P368010-32 7.010.0 Flameproof packing type P368010-33 10.112.0 Packing connector unit Table4 Flameproof packing type cable ground (Option) Cable Flameproof packing type connector unit 17 7.Adjustment Caution ! (1) For this positioner, span and zero point adjustment of each actuator is necessary.
Weight9 kg 32 For option T : 39 *1 Use the product in conditions where freezing will not occur.
How-to-Order 10 Mounting and Installation 15 Air Supply 16 Supply Pressure 16 Piping 16 Connections V port (when the vacuum pressure switch is installed) 17 Solenoid Valve 19 Construction 23 Maintenance and Inspection 24 How to replace the Silencer 25 How to replace the Suction Filter 26 How to order replacement 27 Manifold Products 28 Exhaust from Ejector 30 Specifications 30 Circuit diagram 32
(Refer to page 32) (kPa/MPa/Pa can still be selected if the product does not have the units selection function.) : Refer to page 9 for LCD of corresponding unit. Press the SET button to set. Return to function selection mode.
Tubing for AD27-D: I.D. 2.5 (3/32") or larger, Length 5 m (200 inch) or shorter Tubing for AD37, 47(N)-D: I.D. 4 (3/16") or larger, Length 5 m (200 inch) or shorter Tubing for AD38, 48(N)-D: I.D. 6.5 (1/4") or larger, Length 5 m (200 inch) or shorter Air Source Warning (1) Use clean air.
When hysteresis mode is selected: Refer to page 32. When window comparator mode is selected: Refer to page 33. When accumulated output mode is selected: Refer to page 34. When accumulated pulse output mode is selected: Refer to page 36. -31No.PF-OMS0002-B a. When hysteresis mode is selected Set value [P_1] or [n_1] is displayed on the main display.
Grease pack part number: GR-S-010 (10g), GR-S-020 (20g) Refer to Page 32 for made to order product (XC85). 1) Rod seal Apply a thin layer of grease to all surfaces of the new seal to make it easy to mount the rod seal and improve sealing.
Table 1: Stroke adjustment range (Without spacer, with short spacer, with long spacer) -10 -20 -30 -40 -50 0 0 to 10 10 to 20 20 to 30 L unit MY2*16 Without spacer Short spacer Long spacer H unit 0 to 12 12 to 24 24 to 36 L unit MY2*25 Without spacer Short spacer Long spacer H unit 0 to 16 16 to 32 32 to 48 L unit H unit Without spacer MY2*40 Short spacer Long spacer -9- Warning 1.
ZFC1 ZFC3 ZFC5 ZFC7 5 20 L/min 750 mm 2 7 100 L/min 1260 mm 1 2 2 3.2 3 4 4 6 5 8 6 10 7 12 Inch size A 1/8 B 5/32 D 1/4 E 5/16 F 3/8 7 - 2-2 Specifications Specifications Remarks Fluid Air, Nitrogen This product cannot be used in an environment exposed to chemicals. The maximum operating pressure varies depending on the temperature.
Procedure 3Power supply OFF ( Power supply ON) 32 - 5. Wiring of cables / Common precautions Warning 1. Adjusting, mounting or wiring change should never be done before shutting off the power supply to the product. Electrical shock, malfunction and damaged can result. 2. Never disassemble the cable. Use only specified cables. 3.
Compact Cylinder/Non-rotating Rod: Double Acting, Single Rod Series CQ2K Replacement Procedure is 12, 16, 20, 25 32, 40, 50, 63 P.290 Construction Standard (40 to 63) !4 !5 !3 !4 !5 !3 With auto switch Without auto switch The numbers are the same as the "Construction" of the CQ2 series catalog (CAT.ES20-205). *BLUE links will lead to purchase pages.
Compact Cylinder/Non-rotating Rod: Double Acting, Double Rod Construction Series CQ2KW 12, 16 20, 25 32, 40 50, 63 Replacement Procedure is P.290 Standard (40 to 63) Actuators Modular F.R.L. Pressure Control Equipment Air Preparation Equipment Industrial Filters Replacement Procedure Actuators Modular F.R.L. Pressure Control Equipment Industrial Filters !6 !8 !5 !7 !6 !8 !5 !
Compact Cylinder/Plate Type: Double Acting, Single Rod Series CQU 20, 25, 32, 40 Construction !2 !0 o !3 i !1 The numbers are the same as the "Construction" of the CQU series catalog (CAT.ES20-198). *BLUE links will lead to purchase pages. Seal Kit List Description Material Note No. Replacement Parts: Seal Kit Kit no.
Contents Bore size (mm) RQB20-PS RQB25-PS RQB32-PS RQB40-PS RQB50-PS 20 25 32 40 50 63 80 100 RQB20-PS RQB25-PS RQB32-PS RQB40-PS RQB50-PS RQB63-PS RQB80-PS RQB100-PS Cushion needle 12 Stainless steel Check seal 13 NBR Check gasket 14 NBR Set of left nos. !6, !7, !8. Needle gasket 15 !6 !7 !