I/O Configurator (NFC version) The wireless slave unit does not operate with the set input/output size. 8 Check the system configuration on the Information tab of the wireless master to identify the unit with an error. Check the diagnostic information from the Description to identify the error. For diagnostic information of each unit and details, refer to section 3.4.1 Information tab (page 40).
The wireless slave unit does not operate with the set input/output size. 8 Check the system configuration on the Information tab of the wireless master to identify the unit with an error. Check the diagnostic information from the Description to identify the error. For diagnostic information of each unit and details, refer to section 3.4.1 Information tab (page 40).
500 500 500 0 0 0 0 10 20 30 40 50 0 0 2 4 6 8 10 12 14 16 0 4 8 12 16 20 24 0 10 20 30 40 50 60 Work load [kg] Work load [kg] Work load [kg] Work load [kg] 2000 2000 2000 2000 Mey 1500 1500 1500 1500 L5 [mm] L5 [mm] L5 [mm] L5 [mm] m 1000 1000 1000 1000 Wall L5 Y 500 500 500 500 0 0 0 0 4 8 12 16 20 24 0 10 20 30 40 50 0 0 2 4 6 8 10 12 14 16 0 10 20 30 40 50 60 Work load [kg] Work load
Perform an echo back test for the controller with controller ID:1.
In the ON condition an indicator LED will show, and any connected load will be powered. In the OFF condition, there will be no indicator LED and no power supplied to the load. An output showing such behavior is called switch output.
An application which has the possibility of having negative effects on people, property, or animals, requiring special safety analysis. d. When used in an interlock circuit, dual interlock such as mechanical protection is necessary in case of accident. Periodical inspection is also necessary to confirm proper operation.
Furthermore, an abnormal temperature rise due to adiabatic compression can cause tubing to burst. Note 3) The minimum bending radius indicates the value at a temperature of 20C with an outside diameter rate of change of 10% or less. At higher temperatures the outside diameter rate of change may exceed 10% within the minimum bending radius.
an external temperature sensor is displayed.
Note 3) For the inch-size One-touch fittings, refer to page 4-14-40.
Nil C 0.4 to 4 l/min 1.8 to 20 l/min 4 to 40 l/min 04 20 40 The cable and connector are shipped unassembled.
1 Stainless Steel Cylinder Series CJ5-S Series CG5-S 10, 16 20, 25, 32, 40, 50, 63, 80, 100 Applicable for use in an environment with water splashing such as food processing, etc. RE A B REC Uses grease for food processing machines that meets FDA (U.S.
1 Stainless Steel Cylinder Series CJ5-S Series CG5-S 10, 16 20, 25, 32, 40, 50, 63, 80, 100 Applicable for use in an environment with water splashing such as food processing, etc. RE A B REC Uses grease for food processing machines that meets FDA (U.S.
An application which could have negative effects on people, property, or animals requiring special safety analysis. 4. Use in an interlock circuit, which requires the provision of double interlock for possible failure by using a mechanical protective function, and periodical checks to confirm proper operation. 1.
AXT100-DR7 L dimension Select L dimension from the table below and enter an applicable symbol.
mm, V = 200 mm/s or less 100 100 Load mass m (kg) Load mass m (kg) 50, 63 50, 63 50, 63 50, 63 32, 40 32, 40 10 10 32, 40 32, 40 25 25 25 20 25 20 20 20 1 1 10 100 50 51 200 10 100 50 51 200 Stroke (mm) Stroke (mm) (19) L = 50 mm, V = 400 mm/s (20) L = 100 mm, V = 400 mm/s 100 100 63 63 50 50, 63 50, 63 50 10 10 40 40 Load mass m (kg) Load mass m (kg) 40 40 32 32 32 32 25 25 25 25 20 20 20
Install an air filter. Install an air filter upstream near the valve. Select an air filter with a filtration size of 5 m or smaller. 2. Take measures to ensure air quality, such as by installing an aftercooler, air dryer, or water separator. Compressed air that contains a large amount of drainage can cause a malfunction of pneumatic equipment such as valves.
When disassembling a cylinder with a bore of 20 to 40, use a vise or the like to hold the wrench flats portion of the tube cover or the rod cover on one side, while placing a wrench or an adjustable wrench on the other side to loosen and remove the cover. To replace, tighten it an additional 28 from the installed position.
Hmm 0.3MPa 0.7MPa 0.3MPa 60 0.7MPa 0.4MPa 60 0.4MPa 40 40 20 20 100 80 60 40 20 0 100 0 80 60 40 20 Gripping point L mm Gripping point L mm 12-3-6 7 Model Selection Series MHF2 Confirmation of External Force on Fingers: Series MHF2 Step 3 MHZ L L MHF MHL Mr Mp Fv My MHR MHK MHS L MHC MHT MHY L: Distance to the point at which the load is applied (mm) MHW Maximum allowable moment Allowable
60 40 20 0 0 50 30 10 Gripping point L mm Gripping point L mm MHF2-16D MHF2-20D 100 0.5MPa 100 Pressure 0.2MPa Pressure 0.2MPa 80 0.5MPa 0.6MPa 80 0.6MPa Overhang Hmm Overhang Hmm 0.3MPa 0.7MPa 0.3MPa 60 0.7MPa 0.4MPa 60 0.4MPa 40 40 20 20 100 80 60 40 20 0 100 80 60 40 20 0 Gripping point L mm Gripping point L mm 12-3-6 7 Model Selection Series MHF2 Confirmation of External Force on Fingers
e Order No. b d f l1 c a 32 M10x1.25 GKM10-20 10 40 10 52 20 20 40 M12x1.25 GKM12-24 12 48 12 62 24 24 50/63 M16x1.5 GKM16-32 16 64 16 83 32 32 80/100 M20x1.5 GKM20-40 20 80 20 105 40 40 Rod end nut (standard equipment) 30 d D C H B Bore size (mm) Order No.