Solid State Auto Switch (Refer to the installation manual) Connect frame-ground terminal (FG terminal) to the ground when using a switching power supply. Do not drop, hit or apply excessive shock (larger than 1000 m/s2) to the Auto switch. Otherwise it can result in damage to the Auto switch causing failure or malfunction. -5No.D-S-OMK0010-H Wiring Do not pull the lead wires.
(Refer to the installation manual) Connect frame-ground terminal (FG terminal) to the ground when using a switching power supply. Do not drop, hit or apply excessive shock (larger than 1000 m/s2) to the Auto switch. Otherwise it can result in damage to the Auto switch causing failure or malfunction. -5No.D-S-OMZ0004 Wiring Do not pull the lead wires.
Be sure to ground terminal FG when using a commercially available switch-mode power supply. Never mount an actuator equipped with Auto switch in a location that will be used as a foothold. The product may be damaged if excessive force is applied by stepping or climbing onto it. Do not drop, hit or apply excessive shock to the Auto switch.
Connection to ground Install the grounding cable as shown in the figure Cable with crimping M4 Screw M4 FG terminal Caution M4 screw, the cable with crimped terminal and toothed washer must be prepared by the user. The actuator must be connected to Ground to reduce noise. If further noise resistance is required, consider measures such as grounding 0V (signal ground).
Functional ground (When the controller is mounted, tighten screws and connect the grounding cable) FG 17 No.JXC-OMY0002-A 3.3 Outside dimension diagram The outside view of this product is as shown in the diagram below: 1 Screw mount type JXC5H7-JXC6H7For body mounting(Thread mounting type) 2 DIN rail mount typeJXC5H8-JXC6H8(when DIN rail is unlocked) (when DIN rail is locked) *DIN rail
P.256.3 P.21 10 No.JXC-OMU0004-A 3. 31 2 HB DC24V102 (1) * UL , UL1310 Class2 6 () 6 () 14 114E A/B 800p/r EEPROM LED LED/1 7 LED 1 7 3 16 10 [10][15][A][F] I/O 5m 20m [] 040 [%RH] 90 ) [] -1060 90 ) [RH] 50MDC500V 130g 150gDIN 1 2 37 LED 10 [10][15] 10 10 11 12 13 14 15 16 A b c d E F 11 No.JXC-OMU0004-A 3.2 PWR LED ON/ : ON/OFF : ALM ON/ ON/: LED SW (SW , ) FG
Functional ground (When the driver is mounted, tighten screws and connect the grounding cable) (10) FG 18 - 3.3 Outside dimension diagram The outside view of this product is as shown in the diagram below: (1) Screw mount type (LECPA-) (2) DIN rail mount type (LECPAD-) 19 - 3.4 How to install (1) How to install The driver can be direct mounted using screws or mounted on a DIN rail.
(Refer to the installation manual) Connect frame-ground terminal (FG terminal) to the ground when using a switching power supply. Do not drop, hit or apply excessive shock (larger than 1000 m/s2) to the Auto switch. Otherwise it can result in damage to the Auto switch causing failure or malfunction. -5No.D-S-OMB0023-C Wiring Do not pull the lead wires.
Be sure to ground terminal FG when using a commercially available switch-mode power supply. Do not drop, hit or apply shock to the Pressure Sensor. Otherwise damage to the internal parts can result, causing malfunction. Do not pull the lead wire forcefully, not lift the product by pulling the lead wire.
Be sure to ground terminal FG when using a commercially available switch-mode power supply. Do not drop, hit or apply shock to the Pressure Sensor. Otherwise damage to the internal parts can result, causing malfunction. Do not pull the lead wire forcefully, not lift the product by pulling the lead wire.
contact (CLOSE During Alarm) Alarm Output Temperature Alarm a connector 6 7 8 9 6 contact (OPEN During Alarm) D-sub 9 pin (Pin type) 7 Temperature Alarm Fixed screw: M2.6 Common Temperature Alarm b 8 contact (CLOSE During Alarm) 3 Resistance Bulb Terminal A 8 1 4 Resistance Bulb Terminal B External temperature 5 Resistance Bulb Terminal B 15 9 sensor D-sub 15 pin (Socket type) connector 15 FG
Terminal block arrangement A-phase pulse input B-phase pulse input Bank 1 selection Bank 2 selection (UP pulse) (DOWN pulse) Sensor power Sensor power FG terminal Control input Sensor input Sensor input Reset input Hold input common common common output GND DC12V ..
(j) (d) FG (k) (l) (e) Mode switch Swich the mode between manual and auto. (m) Auto mode / Without alarm: Indicates the position number which is command by ON/OFF of IN0 to IN3 of the CN4 parallel I/O. (During command operation: Flashing / Instruction command completed: ON) Auto mode / With alarm: Indicates Alarm Group.
Ensure that the FG terminal is connected to ground when using a commercially available switchmode power supply. Do not drop, hit or apply excessive shock to the product. Otherwise damage to the internal parts of the product, solenoid valve and internal parts of the pressure switch can occur, causing malfunction.
contact (CLOSE During Alarm) 4,5 Unused Alarm Output connector 6 Temperature Alarm a contact (OPEN During Alarm) 7 Temperature Alarm Common 8 Temperature Alarm b contact (CLOSE During Alarm) 9 Unused 1,2 Unused External temperature sensor connector 3 Resistance Bulb Terminal A 4 Resistance Bulb Terminal B D-Sub 15pin (Socket) Fixed screw : M2.6 5 Resistance Bulb Terminal B 6-14 Unused 15 FG
Cover panels of the product should be opened only by qualified service technicians or qualified personnel. 15 FG Circulating fluidWater Circulating fluid flow rate3L/min Facility water flow rate10L/min Wetted materials SUS304 Circulating fluidEthylene glycol 20% Circulating fluid flow rate3L/min Facility water flow rate10L/min 2500 2500 Power supply Single phase AC100 to 240V(+/10%), Single
Functional ground (When the controller is mounted, tighten screws and connect the grounding cable) FG 20 - 3.3 Outside dimension diagram The outside view of this product is as shown in the diagram below: (1) Screw mount type JXC517#-#, JXC617#-# For body mounting (Thread mounting type) (2) DIN rail mount type JXC518#-#, JXC618#-# 167.3 (when DIN rail is locked) 167.3 (when DIN rail is locked
Ensure that the FG terminal is connected to ground when using a commercially available switch-mode power supply. Do not drop, hit or apply excessive shock to the product. Otherwise damage to the internal parts of the product, solenoid valve and internal parts of the pressure switch can occur, causing malfunction.
Be sure to ground terminal FG when using a commercially available switch-mode power supply. Do not drop, hit or apply shock to the Pressure switch. Otherwise damage to the internal parts can result, causing malfunction. Do not pull the lead wire forcefully, not lift the product by pulling the lead wire.
Use a protective cover. 15 FG Do not mount the product in a location where it is subject to strong 3.5 Model number of product vibrations and/or shock.