SMC Pneumatic Clean Series

R T (mm) (mm) Rod end male thread Applicable bore size V W X U R S T Q Part no.

Low Profile Guide Type

+ Stroke) Q + Stroke CY1F 4 x MM thread depth ML (LL) LA 6 x YA recessed area Note 2) XAH7 PA Adjustment bolt Max. approx.

15

Load Blocking Xb,Xc,Xd zb A za CY3B CY3R Wb X Z CY1S CY1S Wc yc yd CY1L Wa Wd CY1H Y zc,zd Y CY1F CYP Mass and center of gravity of the load Calculation for Overall Center of Gravity Center of gravity mt = mn q Load no.

Large Size 3 Port Solenoid Valve VP3145/3165/3185 Series Rubber Seal

Disassembly 1) After loosening the screw q, then if the housing r is pulled in the direction of the screw, the connector will be removed from the body of equipment (solenoid, etc.). 2) Pull out the screw q, then remove the gasket or . 3) On the bottom part of the terminal block e, theres a cut-off part (indication of an arrow) .

WRF100

Fixing method for protective covers WRF100-T200 WRF100-S200 WRF100-T240 WRF100-S240 WRF100-T270 WRF-C200 WRF-C240 w WRF-C270 Tightening torque for cover mounting bolts Location Tightening torque (N.m) t r e r y 3.0 to 4.0 5.0 to 7.0 1. q Mount the cover L (q) and cover R (w) on the cylinder body. Mount the cover L (q) on the side where a limit switch is mounted.

Vacuum Pad with Ejector ZHP Series Pad Diameter: ø63, ø80 ZK2 ZQ Ejector and pad are integrated. ZR Space saving and reduced piping labor! Bellows type with groove ZB ZA Two-stage ejector ZX More efficient ejector 30% reduced 50% increased ZM Air Suction

(Refer to q shown in the figure below.) If the lock plate is not locked completely, the pad may drop due to the vibration or load during operation. q ZA Holder y ZX Non-rotating hole Plate ZM 3. To ensure the safety, be sure to mount the lock screw on the lock plate before use. (Refer to w shown in the figure below.)

Rotary Cylinder Series MRQ Size: 32, 40 1

.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com CRA1 CRQ2 MSQ MRQ D20Component Parts No. q w e r t y u i o !0 !1 !2 !3 !4 !5 !6 !7 !8 !

RQ

Working principle A + A' A' q When the piston is retracting, exhaust is discharged from both A and A' until piston seal H passes the air passage A. After piston seal H has passed the air passage A, exhaust is discharged only from A'. The section marked with diagonal lines becomes a cushion chamber, and a cushioning effect is achieved.

MLU

4 @1 u q !3 !2 @6 t @4 w @8 r !1 @5 @3 @2 e !6 CL A CL1 MLGC CNG A MNB C Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com B CNA M(D)LUB25 CNS y CLS !9 i o !5 @0 CLQ Extension locking w q MLGP Section A-A' !

0.5

Red flashes if the CPU is abnormal. q w e r t y u Green lights up when emitters require cleaning.

Suction Guard (Produced upon receipt of order) FHG Series

Port size q Seal order no. r Seal order no. t Seal order no.

Vacuum Filter AFJ Series

q r r w w (y) e (y) t e t Component Parts No.

Direct Operated Precision Regulator Series ARP20/30/40  Sensitivity: Within 0.2% F.S.  Expanded lineup  ARJ 3 types of set pressure and the body size AR425  Energy saving, Air consumption: allow more freedom in designing a circuit. to 935 80% reduct

When the inlet pressure is shut off and released, the check valve w opens and the pressure in the diaphragm chamber q is released to the inlet side (Figure 2). This lowers the pressure in the diaphragm chamber q and the force generated by the pressure regulator spring e pushes down the diaphragm.

Direct Operated Precision Regulator ARP20/30/40 Series  Sensitivity: Within 0.2% F.S.  Expanded lineup  ARJ 3 types of set pressure and the body size AR425  Energy saving, Air consumption: allow more freedom in designing a circuit. to 935 80% reduct

When the inlet pressure is shut off and released, the check valve w opens and the pressure in the diaphragm chamber q is released to the inlet side (Figure 2). This lowers the pressure in the diaphragm chamber q and the force generated by the pressure regulator spring e pushes down the diaphragm.

Direct Operated Precision Regulator/Modular Style (For Special Applications) - ARP20 to - ARP40 Direct Operated Precision Regulator with Backflow Function/Modular Style (For Special Applications) - ARP20K to - ARP40K 10 20 21 10 20 21 10 20 21 10 20 21

When the inlet pressure is shut off and released, the check valve w opens and the pressure in the diaphragm chamber q is released to the inlet side (Figure 2). This lowers the pressure in the diaphragm chamber q and the force generated by the pressure regulator spring e pushes down the diaphragm.

air-filter-e

KT-FGDC KT-FGDE KT-FGDT KT-FGDF Replacement parts A 1 kit for each of each one of seals q to t and gasket.

1.63

position is changed, go back to step q.

MHC2

9 MHC6-PS Seal kit MHCA2-6 (Short body type) Double acting/With fingers closed Single acting Double acting/With fingers open o i e q t !1 !6 w !0 r !4 u !5 !7 y !3 !2 Component Parts Material Note Material Note No. Description No. Description Hard anodized Aluminium alloy High carbon chromium bearing steel Body Needle roller q !

10

3 e o i q @6 @7 @3 @5 !9 !0 !2 !1 !6 !4 Component Parts No. Description Material Note 1 Body Aluminum alloy Hard anodized No.

3-Position Rotary Table

Thus, the total air consumption Q of the rotary table and tubing is obtained as shown below.