Do not apply external force to the coil section. When tightening is performed, apply a wrench or other tool to the outside of the piping connection parts. Caution Pilot port piping 12(P1) and 10(P2) piping should be as follows according to the model. 2. Do not warm the coil assembly with a heat insulator, etc. Use tape, heaters, etc., for freeze prevention on the piping and body only.
When mounting the product, please do not block the exhaust port at the center of the body as this may cause performance issues.
22.5 52h9 0 0.074 +0.030 0 +0.052 0 43 30H9 3-4H9 depth 4 5 4 ( A , B , C ) 3-R2 3-R2 2-6.6 through 21.5 10.5 16 5 53.5h9 0 0.074 7 6 43 23 10.5 46 4 13 Angle adjustment bolt 2-6.6 through 72 13 Adjustment: Max. 10.3 6 2 M5 x 0.8 2 8 A port 1 B port +0.030 0 3-4H9 long groove depth 3 8 g6 0.005 0.014 ( A , B , C ) 16h9 0 0.043 4-M6 x 1 depth 11 50 0 0.074 53.5h9 48 11-5-14 14 Series MSUA
Do not operate a cylinder with its bumper bolt removed. If the bumper bolt is removed, the piston hits the head cover, causing damage to the cylinder. Therefore, do not use a cylinder without a bumper bolt. 2. The piston rod must be retracted when mounting the cylinder.
Display for Wireless Base 14 3.2.1. Information tab 14 3.2.2. Input/Output monitor tab 16 3.2.3. Setting tab 20 3.3. Display for Wireless Remote 30 3.3.1. Information tab 30 3.3.2. Input/Output monitor tab 32 3.3.3. Setting tab 36 3.4. Detailed information of units 41 3.4.1. Information tab 41 3.4.2. Details of I/O monitor tab 50 4. Setting Function 57 4.1. Edit TAG 57 4.2.
Display for wireless master 14 3.2.1. Information tab 14 3.2.2. Input/Output monitor tab 16 3.2.3. Setting tab 20 3.3. Display for wireless slave 30 3.3.1. Information tab 30 3.3.2. Input/Output monitor tab 32 3.3.3. Setting tab 36 3.4. Detailed information of units 40 3.4.1. Information tab 40 3.4.2. Details of I/O monitor tab 49 4. Setting Function 56 4.1. Edit TAG 56 4.2.
Display for wireless master 14 3.2.1. Information tab 14 3.2.2. Input/Output monitor tab 16 3.2.3. Setting tab 20 3.3. Display for wireless slave 30 3.3.1. Information tab 30 3.3.2. Input/Output monitor tab 32 3.3.3. Setting tab 36 3.4. Detailed information of units 40 3.4.1. Information tab 40 3.4.2. Details of I/O monitor tab 49 4. Setting Function 56 4.1. Edit TAG 56 4.2.
D -DIN connector DL -DIN connector with light DO-For DIN connector (without connector) Orifice and port size combinations T -With conduit terminal TL-With conduit terminal/light Class Orifice diameter Port size 2 3 4 5 7 10 1/8 (6A) 2 1/4 (8A) 1/4 (8A) 3 3/8 (10A) 1/2 (15A) Connector 1/4 (8A) 3/8 (10A) 4 All class B coils are equipped with surge voltage suppressor.
Adjustable Rod Lever/VM830-01-14 JIS Symbol 2.3N F.O.F.
o 0.62 322 1.28 14 oaa {4) 250 u-24 0.50 .621 .621 0.25 0.93 0.38 1t-1E .251 .250 0.75 0.25 0.34 0.75 o.75 o.1a cts16 0.75 120 o.62 3.19 3.8:t 343 t06 {17-l _312 6t-21 0.50 .621 .621 0.38 1 . 1 2 0.38 5t-i E .25r .250 0.75 0.25 o.3a 3.97 o.8a o_aao.24 qi-14 o.75 1.30 0.62 334 1.25 125 t 2 5 t 1 k ) 375 \-24 o.aE .749 .749 o.11 r.32 0.50 .251 o.25 0.41 rt.4 1.06 r.06 0.25 sa-l6 0.46 r.62 0.78
Do not use a lubricator on the inlet side of the product, as the bleed mechanism can malfunction. Caution 1. For emergency action in the event of setting failure or leakage from the relief port, refer to Troubleshooting in the Operation Manual of the product. Piping Warning Air Preparation Equipment 1.
Make sure that dust and/or other foreign materials do not enter the valve from the unused port (e.g. exhaust port). The grommet portion contains a breather hole for the core.
When using the male thread mounting type product, do not loosen the bottom nut shown in the figure below. (The bottom nut is intended to secure the connection between the bracket for the adapter connection and the male thread.) PD3 Circuit without release valve (Usage example of vacuum connection) V V PD2 PD2 Supply valve EXH. P Pressure sensor Do not loosen this nut.
Do not use a lubricator on the inlet side of the product, as the bleed mechanism can malfunction. Caution 1. For emergency action in the event of setting failure or leakage from the relief port, refer to Troubleshooting in the Operation Manual of the product. Piping Warning Air Preparation Equipment 1.
Please do the vacuum aspiration according to customer's specification.
Please do the vacuum aspiration according to customer's specification.
Free mount Speed controllers do not protrude from the top of the body. Top mount Bottom mount Side mount Wiring and piping direction can be selected depending on mounting conditions.
Do not service or attempt to remove product and machinery/equipment until safety is confirmed. The inspection and maintenance of machinery/equipment should only be performed after measures to prevent falling or runaway of the driven objects have been confirmed.
Note 2) Do not release the OUT side piping port of the product directly to the atmosphere without connecting piping. If the product is used with the piping port released to atmosphere, accuracy may vary.
Refer to pages 16-14-3 and 16-14-4 for Safety Instructions and Common Precautions on the products mentioned in this catalog, and refer to pages 16-1-11 to 16-1-13 for Precautions on every series. Wiring Pressure Source Warning Warning 4. How to connect contact protection box Connect the lead wires from the body and the contact protective box side indicated SWITCH.