Micro Mist Separator with Prefilter AMH Model Model AMH250 AMH350 AMH450 AMH550 AMH650 AMH850 AMH150 Series AMH can separate and (1) remove aerosol state oil mist in 500 1000 2000 3500 6000 12000 200 Rated flow (l/min(ANR)) compressed air and remove Po Element oil saturation Initial condition Note) Compressed air over max. flow line in the table below may not meet the specifications of the product. It may cause damage to the element. 4.6-17 Micro Mist Separator with Prefilter Series AMH Construction AMH850 AMH150 to AMH650 Component Parts q Description Aluminum die cast Aluminum die cast Material Note No.
When the work holding point is out of range, the unbalanced load applied to the finger and the guide section may cause excessive play in fingers and have an adverse effect on the gripper life.
Applicable auto switch Notes) Some liquid may make the use of an air gripper or auto switch impossible. Confirm the kind of the questionable liquid and consult SMC for the use.
When the work holding point is out of the limit range, the unbalanced load applied to the finger and the guide section may cause excessive play in fingers and have an adverse effect on the gripper life.
The used of turbine oil at temperatures lower than 0C leads to increased viscosity and may cause the valve to malfunction.
Note) GENTLY pull the lead wire, otherwise it may cause contact failure or disconnection.
If it is mounted in the wrong direction, connected equipment may malfunction. Mount it by referring to how to switch over from N.C. to N.O. specifications. Universal porting permits convertibility N.C./N.O. by a simple 180 degree rotation. Mounting conditions for N.C. and N.O. is indicated as below figure. Valve Exhaust port type N.C. N.O. Common exhaust Caution 1.
Otherwise, air leakage may result. Element Clip Fitting assembly To replace an element, remove the cover on the top side of the end plate and remove the old element with a flat head screwdriver, etc.
The used of turbine oil at temperatures lower than 0C leads to increased viscosity and may cause the valve to malfunction.
If it is pulled off at an angle, the pilot valve may be damaged or the protective O-ring may be scratched. Installation Place the cover straight over the pilot assembly so that the pilot valve is not touched, and push it until the cover hook locks without twisting the protective O-ring. (When pushed in, the hook opens and locks automatically.)
Perform periodic inspections and confirm normal operation, otherwise it may be impossible to guarantee safety due to unexpected malfunction or erroneous operation. 4. Do not touch connector terminals or internal circuit elements when current is being supplied.
Also, since there is an internal voltage drop of 4 V, it may not be possible to confirm the OFF and ON states with a tester, etc. R1 R2 n VQC B A VVQ4000 -10A-1 SQ 7 VQ0 B A 6 VQ440 0 1 VQ4
Adjustment outside the prescribed ranges may cause malfunction of the product or failure of switches to operate. MSUA 190 P402070-3A CRQ2X MSQX MSUA 1-180 P402070-3B MSUA 390 P402090-3A MRQ MSUA 3-180 P402090-3B MSUA 790 P402060-3A MSUA 7-180 P402060-3B 2.
Regard values mentioned above as reference only, since actual valves may depend on operating conditions. Note 1) Note 2) Pushing force for adsorption is almost equivalent to return force of buffer spring. Pad shape permits adsorption to sloped surfaces. When a workpiece could be deformed during adsorption or transportion.
Note 2) When holding a workpiece close at the end of open/close stroke of fingers, detecting performance of the combinations listed in the above table may be limited, depending on the hysteresis of an auto switch, etc. 470 Low Profile Air Gripper Series MHF2 Protrusion of Auto Switch from Edge of Body Auto Switch Hysteresis The amount of auto switch protrusion from the body end surface is
Damage to the solid state pressure sensor may occur. Switch assy O ring Gasket Base 3.8-4 ISA Dimensions/Centralized Wiring (Terminal Block Box Style) Unit Manifold With bracket Deflection level indicator Terminal block box 34 L2 40 34 L1 Deflection level indicator Terminal block box 75 40 90 10 10 10 Rc1/8 SUP.
Otherwise, it may result in a malfunction. 1. Float type auto-drain (N.O.) 1) Use compressor with capacity more than 3.7 kw {400 l/min Be sure to pipe auto-drain under the following conditions. Otherwise, it may result in a malfunction. 1. Float type auto-drain (N.O.) When making drain exhaust piping, use piping with bore size 10 or larger than 10. Length should be shorter than 5 m.
Note 2) Use caution not to tighten excessively when mounting a pressure gauge, otherwise it will may result in a breakdown. (Fastening torque recommended: 7 to 9 Nm.) For sealing, use a pipe tape.
LVC The tubing r may slip if there is oil or dust, etc., on the holder assembly y. Remove the contamination using alcohol or another suitable cleaner. LVA Press the insert bushing e into the tubing r by turning the lever q. (Pressing in can be accomplished with 2 or 3 turns of the lever q.) 4 LVH M type LVD !
Caution VC VDW Quality of Operating Fluid Caution VQ Please note that using fluids that contain foreign mterial (especially hard objects like glass chips), may cause damage to the valve, will reduce sealing performance, and may cause early failure.