LV50-OMQ0004 T Temperature characteristics Indicates the change in the display value and analogue output caused by ambient temperature or fluid temperature changes. W Water hammer Water hammer is a pressure surge due to pressure spread. It occurs when a fluid in motion is forced to stop or change direction when equipment, such as valve is opened/closed.
Dimensions 4 EXH port 1/8 Input signal port( PIL ) R port Supply pressure exhaust port 2 x 1/8 Output port 2( A ) Supply port on the other side 1( P ) 2 x M6 x 1 thread depth 8 (Panel mounting screw) Panel mounted Bracket mounted 2 x 6.5 hole (Mounting screw M6 x 1 x 12) Handle side 4 x M6 screw 4 x 7 hole on the bracket side Bracket plate thickness t = 2 Panel plate thickness t = 3 or less
Command Status Check sum code Test transmission Command Block # 0 0 T S [CR] Unit No. Command Text Check sum code Response Block # 0 0 T S [CR] Unit No. Command Text Error Check sum code status Error status details Code Meaning 0 No troubles 1 Life of E2ROM (cannot write in): Consult the shop or SMC Corporation. 2 Parity error of E2ROM: Reset memory.
For HAA71522 series Power cord Terminal Insulated ring terminal Customer connection side Terminal screw : M3 Connector width :6.5mm Suitable wire :0.75mm2 For HAA37 series Customer connection side Terminal screw : M3.5 Connector width :8.3mm Suitable wire :0.75mm2 HAA Series 12 9 1)Terminal Assembly (Symbol: T) ATX-OM-F004E Air-Cooled Aftercooler 9.
Port 3(R) A G A Unit: mm Model A B C Fn Fd G J XLAV-16-2 40 108 38 30 17 41 XLAV-25-2 50 121 48 40 26 46 XLAV-40-2 65 171 66 55 41 54.5 XLAV-50-2 70 185 79 75 52 61 XLAV-63-2 88 212 100 87 95 70 80.5 XLAV-80-2 90 257 117 114 110 83 90.5 Model K L M N S T XLAV-16-2 17.2 10.2 3.6 3.6 M5 M5 XLAV-25-2 21.4 10.2 3.6 3.6 M5 M5 XLAV-40-2 33.9 10.2 3.6 3.6 M5 M5 XLAV-50-2 38.2 10.2 3.6 3.6 M5 M5
Specification 1.1 AC servo motor 1.1.1 How to order L E J S 100 T9 B 500 T X400 Lead [mm] Motor type Stroke [mm] H 50 200 200 T9 AC servo motor to to A 25 1500 1500 B 10 *Refer to the applicable stroke table.
Jun T TT UT VT . ZT AT BT . Keep the facility water temperature between 10 and 35C. (No dew Jul U TU UU VU . ZU AU BU . condensation). Note that the cooling and heating capacity is changed depending on facility water temperature. Also, if lower-temperature facility water is supplied, dew may condense in the product and the equipment could be damaged.
Switch output T Temperature characteristic The amount of variation in the analogue output or display value when the ambient temperature is changed. U Function to change the unit in which the value of flow is displayed. Only a product with this function can change the unit. A product with unit selection function cannot be purchased if it is used within Japan.
Although the T side will not be used, plugs will not be necessary since it is sealed with the valve The DIN rail used with Series SY9000 is stronger than that used with Series SY3000 and SY5000. Use this exclusive DIN rail with Series SY9000.
ITV2-OM00095-C P R O D U C T N A M E E/P Regulator (DeviceNetTM type) MODEL/ Series/ Product Number ITV1000/2000/3000/2090-DE* Series Install and operate the product only after reading the Operation Manual carefully and understanding its contents. Specifically, read the safety instructions carefully. Keep this operation manual available whenever necessary.
MY1HT series is held by T slot at the bottom. Fig. 2: Holding the product from the top Fig. 3: Holding the product from the bottom (Head cover at both ends) (Head cover, T slot only for MY1HT) At least 5mm of both ends of the cylinder tube have to contact with the attachment point.
Be sure that no ground connection is made to dV dt = Voltage ratio Voltage rise % on zero-cross point dV t a water pipe, gas pipe and lighting rod. Time dt Power cable The power cables are to be prepared under your responsibility, referring to the following table.
Likewise, if a tube is bent or multiple elbow fittings are used, the piping Output shut off alarm function Jun T TT UT VT . ZT AT BT . resistance will increase and the flow rate will decrease. If the flow rate falls, the temperature stability will decrease.
LEC-CK4-1: 1.5 m, LEC-CK4-3: 3 m, LEC-CK4-5: 5 m (2) Derails of input / Output signal T erminal Insulation color Dot Mark Dot color Function Contents No.
Typ. 1 5 16 H-6 11 T-6-L6-6 IM6-L6-6-L6 Page 3 Distributed by Power Aire, Inc. www.poweraire.com sales@poweraire.com Tube to Tube Fittings Distributed by Power Aire, Inc.
1 MHM-32D1-X6400 80.2 39 A T (6) 2 MHM-32D2-X6400 81.2 30 (7) 3 MHM-32D3-X6400 82.2 (8) 50 B C Bumper dimensions Caution Since a thin plate is used for the metal surface on the end, damage may occur when an impact load is applied due to contact with a workpiece.
9 u t MDHR3 !4 !3 q !1 @0 @1 w o e i !5 MHZ MHF r !7 !6 t !8 !0 !2 i !9 y u MHL Component Parts MHR MHR Description Material Description Material Note No. Note No.
1 r #5 @3 @8 #6 y u t !5 #7 #8 @6 w !6 e &0 q &0 #4 #3 $8 $0 %9 ^0 #9 $6 $7 %9 !2 #1 !3 $9 %0 %1 !0 @2 @1 #2 ^2 ^5 $5 %2 @5 ^8 $4 ^1 @4 %4 %5 ^7 $3 #0 $2 %6 @7 ^4 o %7 ^9 ^6 @9 %8 ML2BS $1 %3 ^3 !
tube polyurethane tube Body rotates at 360 around the stud axis 3.18/2.18 x M5 6/4 x M5 MS-5H-6 MS-5ATHU-3 KA 3.18/2 x M5 P.338 KQG2 Hose elbow For nylon, soft nylon, and polyurethane tube Body rotates at 360 around the stud axis 4/2.5 x M5 4/2.5 x M5 MS-5HLH-4 MS-5ATHU-4 For soft nylon and polyurethane tube KG KFG2 6/4 x M5 6/4 x M5 MS-5ATHU-6 MS-5HLH-6 MS MS P.338 P.339 KKA KP LQ MQR T
capacity Size 01 (EVS1-01) and Size 02 (EVS1-02) Interface conforms to ISO 15407-1 Flow rate Cylinder driving size EVS1-01 (Size: 01) EVS1-02 (Size: 02) 100 80 1000L/min (ANR) 400L/min (ANR) Accommodates enclosure IP65 Dust/Splashproof type Light weight Size 01 (3-position): 0.26kg Size 02 (3-position): 0.18kg Series EVS1-01/1-02 How to Order FG S EVS1 01 3 M0 Valve Thread type Size Nil F T