VHK The air will leak to 1(P) port. e Since the valve may have slight air leakage, it may not be suitable for holding pressure in a pressure vessel. Selection One-touch fitting Caution Operation method: To stop the knob in a midway position can cause malfunction. Switch it to ON or OFF quickly and firmly.
SYJ VK Non-locking push flush style VZ Note) GENTLY pull the lead wire, otherwise it may cause contact failure or disconnection. VT Cover Pin VT It is turned ON by pushing the button in the direction indicated by the arrow until it hits the end and turned OFF by releasing the button. VP Groove Connector Part No.
Air source When the balance pressure and the source pressure become equal, fluctuations in the source pressure cause the cylinder's balance pressure to fluctuate, which may cause the cylinder to operate. Therefore, install an air tank on the source pressure side or increase the size of the cylinder that is used.
Auto switches may malfunction if a shield plate is not used.
Regard values mentioned above as reference only, since actual valves may depend on operating conditions. Note 1) Note 2) Pushing force for adsorption is almost equivalent to return force of buffer spring. Pad shape permits adsorption to sloped surfaces. When a workpiece could be deformed during adsorption or transportion.
Faulty sealing of the check valves or accumulation of dust may cause operation to stop, so slurry processing is not available. Refer to page 586 for maintenance parts. Note 1) The values given for discharge and suction head are for no piping. Values will depend on piping conditions.
When used in a conveyor line, the object may be pushed back by the built-in spring force after energy is absorbed. For backlash, refer to the spring force in the specifications. (Pages 886 and 887) 5.
Scratches and gouges may damage the packing, causing air leakage or malfunction. CE1 Operation (RSA) CE2 Caution 1. Do not apply external force from the opposite direction to the end lever type locking mechanism when the lever is locked. When pallets move during conveyor adjustment, first lower the cylinder. 2. Be careful in the space between the cylinder and the lever holder.
Dimensions L, Z, and ZZ are reference dimensions for installing a double knuckle joint, which may be used as a guide. +0.058 0 +0.058 0 +0.058 0 +0.070 0 +0.070 0 0.2 0.4 0.2 0.4 0.2 0.4 0.2 0.4 0.2 0.4 +0.058 0 +0.058 0 +0.058 0 +0.070 0 +0.070 0 107.5 117 127 155 159 107.5 117 127 155 159 115.5 127 137 171 175 CD-MU03 CD-MU04 CD-MU05 CD-MU05 Single Clevis (Pivot Bracket for Double Clevis
When two switches are connected in parallel, malfunction may occur because the load voltage will increase when in the OFF state.
If the valve is energized without air supply, the coil may be burned. Make sure to supply pressure to the valve when energizing. 4. Power consumption 4 W type: Available 2. Please contact SMC for the product usage with a voltage at 75 VDC or more. Standard required by CE mark is different. 3.
Abnormal temperature rise caused by adiabatic compression may result in the tube bursting. 2. The minimum bending radius indicates the value at a temperature of 20C with an outside diameter rate of change of 10% or less. 3. Please exercise caution when using this item in a clean room.
At higher temperatures, the outside diameter change rate may exceed 10% within the minimum bending radius. Caution The TPH series was specially designed for clean blowing and washing lines. Please consult with SMC for use in other applications. Materials: The durability of polyolefin resin against mineral oils is inferior.
Abnormal temperature rise caused by adiabatic compression may result in the tube bursting. 3. The value of the minimum bending radius is measured at the temperature of 20C as shown in the figure above. T T IDK 473
Use a nylon or polyurethane tubing for general industrial water, otherwise the tube may result in being fallen out or bursted when the max. operating pressure is lower and the surge pressure is occurred. 2. Abnormal temperature rise caused by adiabatic compression may result in the tube bursting. 3.
Either may be used. 02 VVEX 2 1 6 Thread type Example for ordering a manifold base: The valve and blanking plate for manifold arrangement should be specified in order from the left side of the manifold base (with the port 2(A) on your side). (Example) VVEX2-2-3-02N * VEX3222-1LO1 2 pcs. * VEX1-17-3A1 pc.
If mounted in a wrong direction, the equipment to be connected may result in a malfunction. Refer to the dimensions for mounting.
Note) GENTLY pull the lead wire, otherwise it may cause contact failure or disconnection. V100 SY Non-locking push type (Tool required) SYJ VK VZ Pin It is turned ON by pushing the button in the direction indicated by the arrow until it hits the end and is turned OFF by releasing the button.
Note) GENTLY pull the lead wire, otherwise it may cause contact failure or disconnection. V100 SY Non-locking push type (Tool required) SYJ VK VZ Pin It is turned ON by pushing the button in the direction indicated by the arrow until it hits the end and is turned OFF by releasing the button.
The period may vary depending on the temperature and other conditions. In some cases the absorber may need to be replaced before the allowable operating cycle above. 14