Vacuum Module: Ejector System Series ZX Note 2) When the product is used for the manifold specification and common exhaust, the exhaust air of the operating ejector releases may enter the vacuum (V) port of the nonoperating ejector and be released if there are an operating and non-operating ejector. Select either the built-in silencer or port exhaust for the ejector exhaust method.
DC voltage (with surge voltage suppressor) If the polarity is incorrect at DC (surge voltage suppressor), diode or switching element may be damaged. As the double solenoid specifications, -X126 and -X135 are available as a special order. (Refer to page 1006.)
Note) Use caution not to tighten excessively when mounting a pressure gauge, otherwise it may result in a breakdown. For sealing, use a sealant tape. PrecautionsWhen drain or oil, etc. gets into the gauge, an error may occur for pressure indication. 751
A bending moment will be applied to the cylinder due to the vibration generated at the stroke end, and the cylinder may be damaged. In such a case, mount a bracket to reduce the vibration of the cylinder or use the cylinder at a piston speed low enough to prevent the cylinder from vibrating at the stroke end.
vary depending on the application and operating conditions. 2) 6 psi (0.04 MPa) differential for CR seat. 3) Tested with inlet pressure 500 psig (3.5 MPa). 4) Weight, including individual boxed weight, may vary depending on connections or options.
DMoisture Control Tube IDK Series When operating an actuator with a small diameter and a short stroke at a high frequency, the dew condensation (water droplet) may occur inside the piping depending on the conditions. Simply connecting the moisture control tube to the actuator will prevent dew condensation from occurring.
Furthermore, abnormal temperature rise caused by adiabatic compression may result in the tube bursting. Note 3) Do not use this product in a manner in which the tube is not fixed. Observe the lesser value of the maximum operating pressure between the tubing and fitting. A material change over a long duration or due to high-temperature may cause leakage.
Zinc die-casted (Black graphite coated) Stud (Surface treatment) Bourdon tube Brass Mass (kg) 0.015 0.01 Caution on handling: When drain or oil, etc. gets into the gauge, it may result in a malfunction. Note 1) When mounting a pressure gauge, use caution not to tighten excessively. Excessive tightening will cause product to be damaged. Use a pipe tape for sealing.
The product may not operate correctly if the pilot valve orice diameter is inadequate. (port size: 3/4, 1) Depending on the pilot piping port size1 or length, the valve may not operate correctly. JSXFA B A Enter the standard product number. 1 The I.D. of the pilot piping must be larger than the pilot valve orice diameter to use. The maximum pilot piping I.D. is 10 mm.
Dimensions may change if the relative humidity changes. Made to Order If you require the moisture control tube with an effective length not listed in the above table, please contact SMC. 1
If you feel any strong resistance and cannot push the sleeve completely to the end side, this may be caused due to jamming. Remove and repeat again by starting from step 1 making sure to secure a gap in the step 3. Port size M3, M5, 3.2, 4 Thread JIS B0209 Class 2 (Metric coarse thread) How to Order M 5 2 AU Note) When installing the tubing, the sleeve must be attached.
Note 4) Due to the construction of this product, it may have more fluctuation in operating speed compared to a rod type air cylinder. For applications that require constant speed, select the equipment corresponding to the required level.
Besides, the whole accuracy after mounting on an equipment may be varied depending on the mounting condition and surroundings. As an equipment, calibration should be done by customer.
Note 6) Due to the softness of polyurethane tubing, it may fold when being inserted. Hold the end of the tubing and insert it all the way in. 840
Note 4) When replacing the pilot valve, it may not satisfy characteristics such as accuracy, etc. Confirm the product works under the operating conditions before using. If SMC is requested to repair the product, SMC confirms whether characteristics are satisfied. Note 5) in the applicable pilot valve part number is designated for the power source/command signal.
The vacuum pressure reached may vary depending on the workpiece (permeability, etc.) Calculate the actual work load in accordance with the vacuum pressure reached. Vacuum pressure reached [kPa] 91 Standard supply pressure [MPa] 0.35 Standard supply pressure Response Time [ms] Nozzle size Pad dia.
(Without a release valve, a workpiece may not be released.) CE marked Manifold Without port Nil 0 2 3 5 Without fitting (M5 x 0.8) Note) CE compliant: For DC only.
Regard values mentioned above as reference only, since actual valves may depend on operating conditions. Note 1) Note 2) Pushing force for adsorption is almost equivalent to return force of buffer spring. Pad shape permits adsorption to sloped surfaces. When a workpiece could be deformed during adsorption or transportion.
Applicable shaft type: X (mm) Y Size 4 to 19.5 50 4 to 21 63 4 to 23.5 80 5 to 30 100 Caution For the shaft patterns A45 and A46, a middle-cut chamfer may interfere with the center hole if the W1/W2 dimensions and (L1 L3), (L2 L4) dimensions are less than what are shown in the tables at right. Symbol: A60 Reverse the assembly of the shaft, and shorten the long shaft.
There may be the case it will vary substantially depending on an ambient environment. Low friction type (CDS1Q): 125, 140, 160 The following set of stainless steel mounting screws is available. Use them in accordance with the operating environment. (Since auto switch brackets are not included, order them separately.)