PSE300.eng Input a set value for pressure to perform switch output.
B A B A B A B A B A B A B HS HS HS HS HS 20 20.6 9 14.6 8.5 14.1 14 10.5 16.1 12.5 18.1 11.9 17.5 19.6 15 24.5 27.3 62 69.7 27 25 20.6 9 14.6 8.5 14.1 14 19.6 10.5 16.1 12.5 18.1 11.9 17.5 15 27 29.8 64.5 72.2 29.5 32 22.6 8.9 16.6 8.4 16.1 13.9 10.4 18.1 12.4 11.8 19.5 21.6 20.1 14.9 30.5 33.3 68 75.7 33 40 27.7 13.9 21.7 13.4 21.2 18.9 26.7 15.4 23.2 17.4 25.2 16.8 24.6 19.9 35 37.8 72.5
Piping specification: -01, -N01 After hand tightening, hold the hexagonal spanner flats of the pressure port with a spanner, and tighten with 2 to 3 rotations. As a reference, the tightening torque is 3 to 5 Nm. When tightening, do not hold the pressure switch body with a spanner. or longer simultaneously.
Piping specification: -01, -N01 After hand tightening, hold the hexagonal spanner flats of the pressure port with a spanner, and tighten with 2 to 3 rotations. As a reference, the tightening torque is 3 to 5 Nm. When tightening, do not hold the Z/ISE20 body with a spanner. Pressure second or longer simultaneously.
A MPa ON kPa OUT1 OFF OUT2 CH 1 2 3 4 PRESSURE Min. B Released SET Work 1 Work 2 Work n Atmosphere Max. A: Maximum pressure value when work piece is adsorbed. A B 4 ON = A A B 4 SET OFF = B + Min. B: Minimum pressure value when work piece is not adsorbed. OUT1 auto preset For adsorption verification: In this mode, repeat the adsorption and release of the work piece for a few times.
Bracket ZS-30-A With M3 x 5L (2 pcs.) Connector for PSE300 ZS-28-C 1 pc. A Note) The bracket is unassembled in the factory, but is included with the shipment.
HS Auto switch 36 12 24.5 SMC SMC A 33 B Auto switch 49.5 A B G 1/2 (applicable cable O.D. 6.8 to 11.5) Proper auto switch mounting positions (mm) D-H7 D-H7C D-H7W D-H7BAL D-C7 D-C8 D-C73C D-C80C D-G39 D-K39 D-A33, D-A34 D-A44 D-B5 D-B6 D-G5NTL D-H7F D-B59W Bore size (mm) A A B A A A A B A B B B B B 20 14 10 8.5 12 10.5 14 9 15 13 12 6.5 8.5 12 7 25 14.5 12.5 9.5 9 11 14.5 9.5 12.5 15.5 11.5
Maintenance Bracket A or D(Model: ZS-24-A/ZS-24-D) Bracket B (Model: ZS-24-B) [01/N01 type] [W1/WF1 type] Operator How to reset the product after power cut or forcible de-energizing The setting of the product will be retained as it was before a power cut or de-energizing.
Open the sealed package inside a clean room. These products are packaged in sealed double packaging in a clean room. It is recommended that the inside packaging be opened in a clean room or other clean environment. 2. Flush out the piping. ITV IC ITVH ITVX Connect these products to piping only after it has been flushed and cleaned properly.
A A1 E1 L1 MM RR1 U1 Part No.
It is set to these values when delivered. 2.1 Communication Procedure This product receives a request message from the master computer and sends back a corresponding response message. It does not send a message firstly.
Plugging one of the cylinder ports (A or B) enables use as a 3 port valve. lt should not be used in special applications such as use as a non-leakage valve. Make sure the exhaust port is open if used as a 3 port valve. Solenoid {X) represents plugged port. common Exhaust ifflg"o,BJ"". rnd Pilot valve I Exhaust air from pilot valve will flow to main valve exhaust port.
Use a watchmaker driver whose grip dia. is 5 to 6mm when tightening the auto switch mounting screw.
Fis. a (9o".18o') How To Read Diagram 270' 1.
It is set to these values when delivered. 2.1 Communication Procedure This product receives a request message from the master computer and sends back a corresponding response message. It does not send a message firstly.
ON/OFF / / 2 3 3 2 1 2 / -20- 3.3. [] LEC LEC / P.32 5.3 <> NPNPNP LEFS16A-100 NPN <> INPIN []INP ON ON INP ON OFF -21- <> No.1 01 a b c d e f g h i j k a ABSINC No. 1 2 mm/s mm mm/s2 mm/s2 % % mm/s % mm mm mm 0 ABS 250 50.00 3000 3000 0 0 0 100 48.00 50.00 0.50 1 ABS 250 0.00 3000 3000 0 0 0 100 0.00 2.00 0.50 ABS()/ / INC()// b c d e f 00 g h i 100%DC24V 250% j 12
Fis. a (9o".18o') How To Read Diagram 270' 1.
This can be prevented by inserting a noise filter, such as a line noise filter and ferrite core, between the switch-mode power supply and the product, or by using a series power supply instead of a switch-mode power supply.
When a filter element is used repeatedly, clean it with air blow or wash it with a neutral detergent. (For 40 m, For 80 m) Check the condition of the element and replace the element with a new one when the specifications are not satisfied.
A IN OUT t A-A BLEED w y Note Component Parts Material No.