2-Color Digital Flow Switch for Air, DIGITAL FLOW SWITCH, 170 lb
2-Color Digital Flow Switch for Air, DIGITAL FLOW SWITCH, 170 lb
SMC's new PFMB dual color digital flow switch allows for a wide range of flow measurement with one product. The PFMB is suitable for use with air and nitrogen. It's compact and space saving with an integrated flow adjustment valve. The bypass struct, 2-Color Digital Flow Switch for Air, DIGITAL FLOW SWITCH, F29, 100 lb
SMC's new PFMB dual color digital flow switch allows for a wide range of flow measurement with one product. The PFMB is suitable for use with air and nitrogen. It's compact and space saving with an integrated flow adjustment valve.
SMC's new PFMB dual color digital flow switch allows for a wide range of flow measurement with one product. The PFMB is suitable for use with air and nitrogen. It's compact and space saving with an integrated flow adjustment valve.
HRX-OM-S004 Installation at indoor site 1 In case of facility having a large installation area (that can vent the air naturally) Make an air outlet on a wall at a high level and air inlet on a wall at a low level, to allow for adequate airflow. 2 In case of facility having a small installation area (that can not vent the air naturally) Make a forced air exhaust vent on a wall at a high level and an air
When a load, such as a relay or solenoid, which generates surge is directly driven, use a type of switch with a built-in surge absorbing element. 8.
cylinder in a stamping application, that moves a 2250 lbs. wieght 60 times per minute through a 6 stoke?
cylinder in a stamping application, that moves a 2250 lbs. wieght 60 times per minute through a 6 stoke?
If the leakage volume is 5 /min (ANR), the vacuum pressure of the S type is 80 kPa r t y, and for the L type it is 47 kPa r' t' y'. Thus, if the leakage volume is 30 /min (ANR) the L type can attain a higher vacuum pressure, and if the leakage volume is 5 /min (ANR), the S type can attain a higher vacuum pressure.
For a facility having a small installation area (that can not vent the air naturally): Make a forced air exhaust vent on a wall at a high level and an air inlet on a wall at a low level. 3.
Since a large quantity of liquid will be pumped out, use a suitable throttle in the discharge port if problems occur. Note 3) With a low number of operating cycles, even a valve with a small Cv factor can be operated.
Leakage voltage Take note that the leakage voltage will increase when a resistor is used in parallel with switching element or a C-R circuit (surge voltage suppressor) is used for protecting a switching device because of the passing leakage voltage through the C-R circuit. The suppressor residual leakage voltage should be 3% or less of the rated voltage. 6.
Refer to page 2. 11 3.5 2-M3 x 0.5 (port size) M3 x 0.5 (Relief port: 10 See above) (Vacuum port: 11 See above) 3.5 3 C + Stroke B + Stroke A + Stroke (mm) Without auto switch With auto switch A B C A B C Bore size (mm) 24 18 29 23 11.5 16.5 6, 8, 10 4 Series CUJ Construction Double acting !3 w e q !1 r y o e t !2 For 4 Built-in magnet Without magnet Single acting u i r y o e w i e u !
Since a large quantity of liquid will be pumped out, use a suitable throttle in the discharge port if problems occur. Note 3) With a low number of operating cycles, even a valve with a small Cv factor can be operated.
Since a large quantity of liquid will be pumped out, use a suitable throttle in the discharge port if problems occur. Note 3) With a low number of operating cycles, even a valve with a small Cv factor can be operated.
Avoid using in a place that exceeds an ambient temperature range. b. Avoid using in a place that exceeds an ambient humidity range. c. Avoid using in a place where condensation occurs due to a drastic temperature change. d. Avoid using in a place in the presence of corrosive or explosive gas or where there is a volatile combustible. e.
1/2(15 A) 3/4(20 A) 1(25 A) Weight(Body) *5 Approx.
At piping This is equivalent to a magnetic field of approximately 18cm in radius from a welding area using a welding current of almost 15,000 amperes. To use the system in a magnetic field that exceeds this value, use a magnetic material to shield the sensor unit Foreign matter should not enter. Entering of foreign matter will cause malfunction.