HRX-OM-M091 The response may not be returned due to noise. If no message is returned after 1sec. of sending a request message, resend the request message. If necessary send a read request message to check if it was written correctly.
The response may not be returned due to noise. If no message is returned after 1sec. of sending a request message, resend the request message. If necessary send a read request message to check if it was written correctly.
The response may not be returned due to noise. If no message is returned after 1sec. of sending a request message, resend the request message. If necessary send a read request message to check if it was written correctly.
Also, the product may have specified durability, running distance or replacement parts. Please consult your nearest sales branch. For any failure or damage reported within the warranty period which is clearly our responsibility, a replacement product or necessary parts will be provided.
Note) It may be difficult to replace the cushion seal #4. Note) For wear ring A of 10, please consult with SMC. Seal kit includes a grease pack (10: 5 g and 10 g, 15: 10 g). Order with the following part number when only the grease pack is needed.
9 @0 @1 @2 @3 24 Cylinder tube gasket NBR REAR10-PS 10 REAR10-PS Wear ring A Special resin 10: not available REAR15-PS 15 REAR15-PS Wear ring B Special resin Piston seal NBR Note 1) It may be difficult to replace the cushion seal @3. Note 2) For wear ring A of 10, please consult with SMC. Seal kit includes a grease pack (10: 5 g and 10 g, 15: 10 g).
. @6, @7, @8, @9, #0, #1, #2 Note) REAS15-PS 15 REAS15-PS Wear ring A 10: Not available Special resin Wear ring B Special resin Note) It may be difficult to replace the cushion seal #2. Note) For wear ring A of 10, please consult with SMC. Seal kit includes a grease pack (10: 5 g and 10 g, 15: 10 g). Order with the following part number when only the grease pack is needed.
. @9, #0, #1, #2, #3, #4, #5 @9 #0 #1 #2 #3 #4 #5 Wear ring A Special resin Wear ring B Special resin Note) Cushion seal #5 may be difficult to be replaced. Seal kit includes a grease pack (10 g). Order with the following part number when only the grease pack is needed.
Otherwise, the impact force may exceed the maximum tensile and compressive force of the product, causing breakage. D-X Technical Data 1141
Also, when using in a vacuum, grease may enter the inside due to the nature of its construction. Rotating Torque/Allowable Number of Rotations 5 32 1 4 5 16 3 8 " " " 0.012 8.3 0.014 6.7 0.020 5 Rotating torque (Nm) (2) Allowable number of rotations (S-1) (3) Applicable tubing O.D.
(Reset type) Perform element replacement when the red ring floats up and covers the entire view port. 0.15 0.1 20/24 16 Pressure drop (MPa) 0.05 0.04 w Operation The hydraulic fluid used becomes high viscosity when the temperature is low during the winter, etc., and the differential pressure indicator or the switch may activate.
(Reset type) Perform element replacement when the red ring floats up and covers the entire view port. 0.1 08 10 12 20 24 16 0.05 Pressure drop (MPa) 0.03 w Operation The hydraulic fluid used becomes high viscosity when the temperature is low during the winter, etc., and the differential pressure indicator or the switch may activate.
Otherwise, the pump will be overloaded and may break. If such a fluid is used, please contact SMC beforehand. 2. TheThermoelectric Bath must not be operated without circulating fluid. The pump breaks by empty driving. 3. The circulating fluid may evaporate, low-ering the level in the tank.
(Example: If ID60 is connected to a 12 tube, air supply may not be sufficient and it may cause malfunction due to the unstable operation of the check valve. 2. Replace the element of the mist separator, installed on the inlet side, on a regular basis. (Refer to the instruction manual of the mist separator for details such as the replacement interval and procedures.)
Do not disassemble the product because it may damage the air cushion mechanism. Contact SMC when disassembly or maintenance is necessary . 169
The number of stations that may be displayed is longer than the manifold number of stations. Example: -D09 Note 2) When -B is selected, a back pressure check valve is included in all stations of the manifold. If the back pressure check valve is used only for the station that need it, then specify the station location in the manifold specification.
Severe clogging of the gauze may result in abnormally reducing discharge volume. At such times, remove the gauze and clean it. 63.5 OUT 14.5 1074
If the flow exceeds the maximum allowable flow for the exhaust cleaner, drainage and oil may be sprayed into the environment causing damage to equipment. 2. Select a model which has a bigger effective area than that of the solenoid valve (including compound effective area). 3.
If the silencer body (case) is made of plastic and is tightened too much, the silencer may be damaged. Please follow the procedures below for mounting. When the body (case) is made of resin Hold the tip of the main body (side without thread) and screw in. At the point where the thread begins to feel tight, use a wrench on the hexagonal flats to tighten an additional 1/4 turn.
Note) Use caution not to tighten excessively when mounting a pressure gauge, otherwise it may result in a breakdown. For sealing, use a sealant tape.