Mini-rotary Actuator Rack & Pinion Style Series CRJ Size: 05, 1 1 Please note that adjusting beyond this range, may cause product malfunction. Note 1) External stopper units for 180 cannot be applied to the 90 Mini-rotary Actuators. Note 2) When using external stoppers for 90, use Minirotary Actuators with a rotation range of 100, and for 180, use actuators with a rotation range of 190.
Otherwise, the adjustment at shipment may deviate. 792
The product specified here may become unsafe if handled incorrectly. The assembly, operation and maintenance of machines or equipment including our products must be performed by an operator who is appropriately trained and experienced. 1.
Regard values mentioned above as reference only, since actual values may depend on operating conditions. Note 1) AMJ Note 2) AMV Pushing force for adsorption is almost equivalent to return force of buffer spring. AEP HEP Pad shape permits adsorption to sloped surfaces. Related Equipment When a workpiece could be deformed during adsorption or transportion.
Confirm that the Output 1 (wh ~ e may have contacted when the output Output 1 (white wire). being unloaded. all the data again I ~ CEI Never apply a wrench to the resin section of Wile) is not contactrlg the power supply.etc and execute RESET was turned ON or be contacting the the main Unit.
While operating, there may be cases where drainage will not easily enter this product. In such a case, adjust the open angle of its bleed valve to lower the pressure a bit inside the bowl, so that drainage will run through easily. Selection Caution 1. The maximum dischargeable drainage rate is 400 cc/min.
Element oil saturation Note) Compressed air over max. flow line in the table below may not meet the specifications of the product. It may cause damage to the element.
Element oil saturation Initial condition Note) Compressed air over max. flow line in the table below may not meet the specifications of the product. It may cause damage to the element.
Element initial condition Note) Compressed air over max. flow line in the table below may not meet the specifications of the product. It may cause damage to the element.
It may cause damage to the element.
auto-drain Drain guide 01 B 06 10 14 B 3 4 1B 1 8 Accessory 02 03 B 1 4 B 3 8 04 B 1 2 1 4 B 1 B 1 2 20 2B IN-OUT reversal direction -T Element service indicator Option HA AT ID AMG AFF AM Misc. 14-20-31 3 Series AMH Flow Characteristics/Select the model taking the max. flow capacity into Element oil saturation Initial condition Note) Compressed air over max. flow line in the table below may
Note) Series AMG is not applicable since there may be cases where water drops ingress inside its differential pressure gauge, resulting in malfunction or damage to the product.
Please note that adjusting beyond this range, may cause product malfunction. Note 1) External stopper units for 180 cannot be applied to the 90 Mini-rotary Actuators. Note 2) When using external stoppers for 90, use Minirotary Actuators with a rotation range of 100, and for 180, use actuators with a rotation range of 190.
This screw should not be removed, because dust may enter inside through the relieving port. Hexagon socket set screw is not prepared for clean room specifications, and use it as relieving port accordingly. Cycle time Due to the nature of its construction, this cylinder starts and stops gradually.
Solenoid valve ( ): Effective area [mm2] : Metal seal Speed controller Composed effective sectional area (mm2) B 9.0 to 14.4 A 3.6 to 6.3 VQ1000 (4.5) VQ1000 (6.3) SY3000 (5.9) SX3000 (5.9) VJ5000 (3.6) VZ3000 (3.6) C 16.2 to 18.0 D 36 to 45 VF5000 (45) E 64.8 to 67 Refer to System selection table, and the appropriate solenoid valve, speed control valve ad bore size may be selected.
In case of horizontal mounting (operation with product facing sideways), malfunction may occur due to load fluctuations.
Scratches and gouges may damage the packing, causing air leakage or malfunction. CE1 Operation (RSA) CE2 Caution 1. Do not apply external force from the opposite direction to the end lever type locking mechanism when the lever is locked. When pallets move during conveyor adjustment, first lower the cylinder. 2. Be careful in the space between the cylinder and the lever holder.
Do not block this port as doing so may lead to a malfunction. Install a silencer if you are concerned about the noise. (There may be a PE port even when the pilot valve’s exhaust is collectively exhausted, such as with the new SY series.)
The SX3000/5000/7000 series was discontinued in May 2020.
Consider the SY3000/5000/7000 series as a substitute.
Some SX series valves may be available for maintenance purposes, so check the part number on the valve and ask your nearest SMC sales office about availability.
Note) SX series valves and SY series valves are not interchangeable mounting or connector wise.