PFG3x.eng Function selection mode Do not operate the product outside of the specifications. Do not use for flammable or harmful fluids. Fire, malfunction, or damage to the product can result. Verify the specifications before use. seconds, to display [F 0]. Select to display the function to be changed [F].
P_2 P_1 Instantaneous flow Set value or 3 4 Set value or 3 Excessive instantaneous flow Do not operate the product outside of the specifications. Do not use for flammable or harmful fluids. Fire, malfunction, or damage to the product can result. Verify the specifications before use. Hysteresis 1 Hysteresis 1 L Flow has exceeded the upper limit of the display flow range. Reduce the flow.
Display accumulated flow Display instantaneous flow Do not operate the product outside of the specifications. Do not use for flammable or harmful fluids. Fire, malfunction, or damage to the product can result. Verify the specifications before use.
Do not use the membrane dryer in an environment containing these chemicals substances.
Do not use this product with special gases, pressure or temperature beyond the specifications. Otherwise, they could cause damage to the product. 4. Post maintenance inspection After installation or repair, perform an appropriate function and leakage test. 5. Modification is prohibited. Do not disassemble or modify the product.
Do not cut the moisture control tube.
EX600-LAB1 Model EX600-LBB1 Do not disassemble, modify (including changing the printed circuit board) or repair. An injury or failure can result. Class B IO-Link port type Class A COM1 (4.8 kbps) COM2 (38.4 kbps) COM3 (230.4 kbps) Depending on connected sensor/actuator Do not operate the product outside of the specifications. Do not use for flammable or harmful fluids.
Do not operate in an atmosphere containing flammable or explosive gases. Fire or an explosion can result. This product is not designed to be explosion proof. Do not operate the product outside of the specifications. Do not use for flammable or harmful fluids. Fire, malfunction, or damage to the product can result. Verify the specifications before use.
Do not operate the product outside of the specifications. Do not use for flammable or harmful fluids. Fire, malfunction, or damage to the product can result. Verify the specifications before use. Error name Error display Error type Troubleshooting method Turn the power off and remove the cause of the over current. Then turn the power on.
Do not cut the insulator. Insert the corresponding wire colour shown in the table into the pin number printed on the sensor connector, to the bottom.
Function Setting Do not disassemble, modify (including changing the printed circuit board) or repair. An injury or failure can result. Mounting screw Function selection mode Do not operate the product outside of the specifications. Do not use for flammable or harmful fluids. Fire, malfunction, or damage to the product can result. Verify the specifications before use.
With regards to a breathing port Do not plug a breathing port. Also take care not to prevent intrusion of foreign matters such as dust and water into the breathing port. Mounting Warning About ventilation If air leakage increases or equipment does not operate properly, stop operation.
Warning Handling (1) Do not use for oxygen. (2) Do not give any modification to the product and its function. (3) Before installation and removal, shut off supply pressure completely and exhaust residual pressure in tubing and other pressure line. -6- Environment Caution (1) Do not mount the product in a location where it is subject to strong vibrations and/or shock. (2) Avoid to expose the
Do not operate at pressures or temperatures, etc. beyond the range of specifications, as this can cause damage or malfunction. (Refer to specifications.) Contact SMC when using a fluid other than compressed air (including vacuum).
Do not use at temperatures (fluid or ambient temperatures) higher than the prescribed operating conditions.
Do not disassemble, modify (including changing the printed circuit board) or repair. An injury or failure can result. Do not operate the product outside of the specifications. Do not use for flammable or harmful fluids. Fire, malfunction, or damage to the product can result. Verify the specifications before use.
Claw 1 Claw 2 Do not operate the product outside of the specifications. Do not use for flammable or harmful fluids. Fire, malfunction, or damage to the product can result. Verify the specifications before use. Error Name Error Display Error Type Troubleshooting Method [2] Turn the power off and remove the output factor for the over current. Then turn the power on.
Do not disassemble, modify (including changing the printed circuit board) or repair. An injury or failure can result. This function is to display error location and content when a problem or an error occurs. Error name Error display Error type Troubleshooting method Do not operate the product outside of the specifications. Do not use for flammable or harmful fluids.
Do not disassemble, modify (including changing the printed circuit board) or repair. An injury or failure can result. Preparation before setting (1)Supply pressure to the product. (2)Place the workpiece on the detection nozzle. Do not operate the product outside of the specifications. Do not use for flammable or harmful fluids. Fire, malfunction, or damage to the product can result.
Do not disassemble, modify (including changing the printed circuit board) or repair. An injury or failure can result. 3 Branch port (COM A to D) 4 Branch port A (COM A) 128 inputs/128 outputs Number of points Do not operate the product outside of the specifications. Do not use for flammable or harmful fluids. Fire, malfunction, or damage to the product can result.