HRX-OM-Q026

HRX-OM-Q026-V Operation Manual Installation Operation Original Instructions Thermo Chiller HRSH Series HRSH100-A-20HRSH100-A-40HRSH100-A-20-S HRSH150-A-20HRSH150-A-40HRSH150-A-20-S HRSH200-A-20HRSH200-A-40HRSH200-A-20-S HRSH250-A-20HRSH250-A-40HRSH250-A-20-S HRSH300-A-20HRSH300-A-40HRSH100-W-20HRSH100-W-40HRSH100-W-20-S HRSH150-W-20HRSH150-W-40HRSH150-W-20-S HRSH200-W-20HRSH200-W-40HRSH200

rep-modular-e

Remove a housing from a body by rotating 4 mounting screws counterclockwise with a hexagon wrench key. Hexagon wrench key Nominal: 5 2) Remove the valve guide. Hold the valve guide with a spanner on the spanner flat to rotate it counterclockwise and remove the valve guide. Spanner Nominal: 30 3) Remove the valve spring. 4) Remove the valve assembly.

Modular Pressure Control Equipment F.R.L. Replacement Procedure

Remove a housing from a body by rotating 4 mounting screws counterclockwise with a hexagon wrench key. Hexagon wrench key Nominal: 5 2) Remove the valve guide. Hold the valve guide with a spanner on the spanner flat to rotate it counterclockwise and remove the valve guide. Spanner Nominal: 30 3) Remove the valve spring. 4) Remove the valve assembly.

3 Port Air Operated Valve

1/8, 1/4 2(A) port 19.5 12 40.5 2 x 4.2 (For mounting) 11.2 30 18.5 1/8, 1/4 3(R) port 1/8 12(PA) port 2A NO 35 43 NC 12 12 3R 1P NC (1/8) 12(PA) port 12 6.7 58.2 18.5 65.2 60 59 24 X 12 M5 x 0.8 (Breathing hole) 19.5 39 1/8, 1/4 1(P) port For vacuum/VPA344V-101 02 A B 1/8, 1/4 2(A) port 19.5 12 40.5 2 x 4.2 (For mounting) 1/8, 1/4 3(R) port 18.5 11.2 30 2A NO 35 43 NC 12 3R 1P NC 1/8 12(

Min. Dripping Flow Rate(l/min): 50, Oil Storage Capacity(cm³): 135, Case: [Resin] Polycarbonate Case, Inlet Side Connection Type: G, Inlet Side Plumbing Thread Nominal: 1/2, Outlet Side Connection Type: G, Outlet Side Plumbing Thread Nominal: 1/2, Drain Exhaust: [Not Provided] No Drain Cock, Flow Direction: [Right] From Left to Right, Size of Body: 40, Accessory: Without optional

Body Size: 40, Thread: F (G), Port Size: 04 (1/2), Mounting: None, Semi-Standard, Body Size 10: Standard, Semi-Standard, Body Size 20: Standard, Semi-Standard, Body Size 30, 40, 50 & 60: Standard

HRX-OM-X037

For a facility with a large installation area that can vent the air naturally: Make an air outlet on a wall at a high level and air inlet on a wall at a low level, to allow for adequate airflow. 2. For a facility with a small installation area that cannot vent the air naturally: Make a forced air exhaust vent on a wall at a high level and an air inlet on a wall at a low level. 3.

HRX-OM-Y098

For a facility with a large installation area that can vent the air naturally: Make an air outlet on a wall at a high level and air inlet on a wall at a low level, to allow for adequate airflow. 2. For a facility with a small installation area that can not vent the air naturally: Make a forced air exhaust vent on a wall at a high level and an air inlet on a wall at a low level. 3.

HRX-OM-W060

For a facility having a small installation area (that can not vent the air naturally): Make a forced air exhaust vent on a wall at a high level and an air inlet on a wall at a low level. 3.

Series 12-CY3B Magnetic rodless cylinder ø15, ø20, ø25, ø32, ø40

In case the mounting orientation is not horizontal, a system with a pressure regulating circuit on the lower side is recommended. (It is also effective to shorten start-up delay in rising and for energy conservation.) 12CY1R/3R Caution 1. Pay attention to the cylinder mounting surface.

VEX-OMO0001

P1 P1 P1 M5 -7VEX-OMO0001 (PE) Best Pneumatics No. () VEX1333-03 G36-4-01 -8VEX-OMO0001 P1 P1 02A 3R (VBA1-10) 3R () PE 3R PE 2A / (VBA1-10) P1 O PE 3R 02A 3R 2A / 2A -9VEX-OMO0001 Revision history 4-14-1, Sotokanda, Chiyoda-ku, Tokyo 101-0021 JAPAN Tel: + 81 3 5207 8249 Fax: +81 3 5298 5362 URL http://www.smcworld.com Note: Specifications are subject to change without

Shock Absorbers and Rate Controls

(t odefReo l M ll P R I U w x (R t o , t,lt'o' 6.3t f ' tl.to.1" l2.roi, r/A 38 N/A 23 6 6.1 I t.2 0.59 Pil/PR0220ctl(s) 234 6.38 -od' o.ls f ' 12.70 iz tz.to|-, N/A 38 N/A 23 6 12 6.1 '|.2 0.77 Prr525CM(Sl 199 e.60Yl t.7o-&' r s.oo l, 25.4 lt.9-3r 5l 25 25 25 N/A 14.3 1.36 PMr55o(il(s) 250 e.60 f , r ?.

Table of Contents

L4 L4 L5 A L5 D3 D3 T T D2 L1 D2 L1 L2 L2 AS ASP Metric Size ASN A M1 L5 Max.

HRL

Use this as a reference.

Series AL modular style lubricator provides accurate lubrication of downstream equipment. The oil drop rate is adjustable depending on equipment requirements. The AL modular design allows connection with other SMC air preparation equipment. Atomizes lubricant into fine particles at uniform rate, Drip rate easily monitored with sight dome, Can be refilled under pressure, High-response time

This is a legacy product. Please contact us for the latest version.sales@ocaire.com, LUBRICATOR, AIRLINE EQUIPMENT, AL MASS PRO, FA, AL MASS PRO 1/2 MODULAR (PT), 1.067 lb

Case: [Resin] Polycarbonate Case, Drain Exhaust: -, Case Guard: -, Specification: Applicable part number: AL20-A, AL30-A, AL40-A, AL40-06-A, AL50-A, AL60-A, Type: Sight dome assembly

As the AL430 and AL40 differ as described above, select a model based on the operating environment and desired application.

As the AL430 and AL40 differ as described above, select a model based on the operating environment and desired application.

Case: -, Drain Exhaust: -, Case Guard: -, Specification: Applicable part number: AL40-A, AL40-06-A, AL50-A, AL60-A, Type: Lubrication plug assembly