Microspeed Cylinder: Double Acting/Single Rod Series CQSX ø 12, ø 16, ø 20, ø 25 Dimensions and auto switch details are equivalent to those of the standard double acting single rod cylinder. Note) Consult with P/A when operating with a stroke below those shown above.
Series AV is a soft start up valve for low-speed air supply to gradually raise initial pressure in an air system and for quick exhaust by cutting off air supply. OSHA compliant, lockable soft start valve, Large effective area, Low power consumption, Modular design, SOFT START-UP VALVE, VALVE, SOFT START LOCKOUT, 243, 1.50000 lb
CM2X32-PS Grease pack (10g): 1 pc. Boss-cut flange type (1 pc.) CM2X40-PS Boss-cut trunnion type (1 pc.) 2. Grease packs When maintenance requires only grease, use the following part numbers to order.
CUX16-PS CUX20-PS M3 0.54 10% CUX25-PS M4 1.23 10% Grease pack (10g): 1 pc. CUX32-PS M5 2.55 10% Due to cylinder structure, 10mm bore size seals cannot be replaced. M6 4.02 10% 2. Grease pack When maintenance requires only grease, use the following part numbers to order. Grease pack GR-L-005 (5g) GR-L-010 (10g) GR-L-150 (150g) Operation Warning 1.
Never mount a product in a location that will be used as a foothold. The product may be damaged if excessive force is applied by stepping or climbing onto it. Do not use this cylinder as a stopper. Minimum adjusting stroke necessary for a positioning stop is 5mm. Operate for 5mm or more before a positioning stop. Ex: 1.
Caution Caution indicates a hazard with a low level of risk which, if not avoided, could result in minor or moderate injury. Warning Warning indicates a hazard with a medium level of risk which, if not avoided, could result in death or serious injury. Danger Danger indicates a hazard with a high level of risk which, if not avoided, will result in death or serious injury. Warning 1.
OUT OUT Proper Auto Switch Mounting Positions (Stroke End) Proper Auto Switch Mounting Positions(Series CE1) Auto switch (mm) Bore size (mm) Auto switch model Symbol 20 32 40 50 63 12 A B A B A B A B A B A B A B A B A B 40.5 47 55 79 82 85.5 D-A7, A8 4 13 17 39 44 41.5 41 47.5 55.5 79.5 82.5 86 D-A7lH, A80H, A73C, A80C, D-F7l, J79, F7lV, J79C 4.5 13.5 17.5 39.5 44.5 42 A B 38 44.5 52.5 76.5
At piping This is equivalent to a magnetic field of approximately 18cm in radius from a welding area using a welding current of almost 15,000 amperes. To use the system in a magnetic field that exceeds this value, use a magnetic material to shield the sensor unit Foreign matter should not enter. Entering of foreign matter will cause malfunction.
Actuator drive When an actuator, such as a cylinder, is to be driven using a valve, take appropriate measures to prevent potential danger caused by actuator operation. 2. Effect of back pressure when using a manifold Use caution when valves are used on a manifold, as actuator malfunction due to back-pressure may occur.
As a result, the cylinder actuates. For this reason, when a workpiece must be lowered, use a cylinder with a built-in brake mechanism so that the cylinder will not actuate.
Consult SMC if using in a place with high vibrations (10G or more) or high magnetic fields. 4. This valve is shipped in the "reset" position (passage: A R). However, it may move to the "set" position during transportation or due to impacts during mounting. Therefore, check the initial position before use by means of a power supply or manual override.
only) 2-4.5 (mounting holes) 67.5 59 19 17 2 R P P R 34 2.3 7 20 Pg.7 4-Rc(PT) 1/8 (ports P, R) A A A P = 19 13.5 L2 L1 4 1 7 8 26 47.5 Approx. 300 (lead wire length) n-Rc(PT) 1/8, M5 x 0.8 (port A) 7 20 34 2-4.5 (bracket mounting holes) 4-M3 x 0.5, depth 6 (bracket mounting screws) 7 8 47.5 15.5 20 25 49 4 L3 7 7 L: Dimension table n: Stations n L 1 35 27 13 2 54 46 32 3 73 65 51 4 92 84
The cancel cap holds the lever horizontally allowing a pallet to pass.
a. b. c. 4. a. b. c. 1 - 1. 1. 1. (), 2. ,, 3. F.G.
Sound absorbing material A 1 9 PVF Suction cover P397114 Sound absorbing material 2 10 PVF Front cover A P397230 O-ring 3 11 NBR End plate 2.79 x 1.02 (NZL) When ordering a vacuum pressure gauge or a digital vacuum pressure switch separately, use the part numbers shown in the option specifications on pages 5 & 6. 4 Body 5 Vacuum sensor unit 6 Nozzle 7 Diffuser Other than vacuum switch P397110
Sound absorbing material A PVF 1 9 P397114 Suction cover Sound absorbing material PVF 2 10 P397230 Front cover A 3 End plate When ordering a vacuum pressure gauge or a digital vacuum pressure switch separately, use the part numbers shown in the option specifications on page 3. 4 Body 5 Vacuum sensor unit 6 Nozzle 7 Diffuser Other than vacuum switch P397110 Detent plug 8 Vacuum switch specifications
Atmospheric release port Air tube Recommended tubing (P/A) TU0425 (polyurethane)