Mechanically Jointed Rodless Cylinder MY1H Series Linear Guide Type: ø25, ø32, ø40 Piping can be connected from 4 directions on the head cover. Allows on-site piping to suit the MY1B installation MY1H MY1H conditions. MY1B MY1M MY1C MY 1500 Piston speed mm/s 100 200 300 400 500 1000 1500 Piston speed mm/s 100 200 300 400 500 1000 1500 Piston speed mm/s MY2C MY2 H/HT Maximum Load Mass Select the load mass from within the range of limits shown in the graphs.
Note 2) The maximum limit is 1000 stroke, but the products that exceed the standard stroke might not be able to fulfill the specifications. Tightening Torque: Tighten the cylinder mounting bolts for the bottom mounting Style (Series CM2RA) with the following tightening torque.
Bore size (mm) Standard stroke (mm) Note 1) Maximum manufacturable stroke (mm) CS1 20 Symbol Specifications CS2 25, 50, 75, 100, 125, 150, 200, 250, 300 1000 25 -X446 PTFE grease 32 Made to Order (For details, refer to pages 1703 to 1896.) 40 Note 1) Intermediate strokes not listed above are produced upon receipt of order.
Max. 2s 2s 1s 1s Min. 0.5s 0.5s 0.2s 0.2s 0.1s 0.1s 0.05s 0.05s 0.02s 0.02s 0.01s 0.01s 6000 100 125 200 300 400 500 700 1000 1500 2000 30004000 10 100 125 200 300 400 500 600700 1000 1500 2000 3000 4000 600 5000 7000 Current (% for breaker capacity) Current (% for breaker capacity) For HRS100-A/W-20-B For HRS150-A/W-20-B HRS100-A/W-40, HRS150-A/W-40 4h 2h 1h 30min 20min 14min 10min 6min
Monitoring of TEMP READY alarm (AL12) does not start since Start Time is set at 1000 sec. Status (6): Monitoring of TEMP READY alarm (AL12) starts at this point where 1000 sec of Start Time has elapsed. Status (7): TEMP READY signal output continues since the temperature is now back within the Out Time range of 200 sec even though it was temporarily outside the Low range.
For product installation at a place of high altitude of 1000 meters or more, select a thermo-chiller of the applicable capacity referring to the table below. 1. Max. ambient temp.: Use the product in lower ambient temperature than the described value at each altitude. 2.
These values orove to de convenient and practical lor ejector sizing purposes. l V = 1 x d ' x ' 4 1000 inside diameter ot tubing (mm), tubing length (meters, m), the lesser capacity of llow, O, or O.
These values orove to de convenient and practical lor ejector sizing purposes. l V = 1 x d ' x ' 4 1000 inside diameter ot tubing (mm), tubing length (meters, m), the lesser capacity of llow, O, or O.
1500 100 200 300 400 500 1000 1500 100 200 300 400 500 1000 1500 100 200 300 400500 1000 1500 Piston speed mm/s Piston speed mm/s Piston speed mm/s Piston speed mm/s Features 6
Minimum operating pressure Without auto switch: 10 to 70C Ambient and fluid temperature (With no freezing) With auto switch: 10 to 60C Piston speed 50 to 500 mm/s Same dimensions as those of the standard cylinder (Series CA2) Cushion Interchangeable Thread tolerance JIS class 2 To 250 st : 251 to 1000 st : 1001 to 1500 st : +1.0 0 +1.4 0 +1.8 0 Stroke length tolerance Lubrication Not required
Magnet: None, Mounting: B (Basic Style), Style: A (Non-lube Air Cushion), Bore Size: 25mm, Stroke: 1000mm, Rod Boot: w/o Rod Boot, Lock Position: W (Lock on Both Sides), Release of Manual: N (Non-locking Type)
Magnet: None, Mounting: B (Basic Style), Style: N (Non-lube Rubber Bumper), Bore Size: 63mm, Stroke: 1000mm, Rod Boot: w/o Rod Boot, Lock Position: W (Lock on Both Sides), Release of Manual: N (Non-locking Type)
Magnet: None, Mounting: Basic Style, Style: Non-lube Air Cushion, Bore Size: 25mm, Stroke: 1000mm, Rod Boot: w/o Rod Boot, Lock Position: Lock on Both Sides, Release of Manual: Non-locking Type, Auto Switch: -, Lead Wire or Prewired Connector: -, Number: -, Auto Switch Mounting Bracket: -
Magnet: None, Mounting: Basic Style, Style: Non-lube Rubber Bumper, Bore Size: 63mm, Stroke: 1000mm, Rod Boot: w/o Rod Boot, Lock Position: Lock on Both Sides, Release of Manual: Non-locking Type, Auto Switch: -, Lead Wire or Prewired Connector: -, Number: -, Auto Switch Mounting Bracket: -
The MB series medium duty tie rod cylinder offers an improved design that enhances cylinder operation and ease of use. The standard air cushion utilizes a floating cushion seal to eliminate piston rod bouncing. The cushion volume has been elevated permitting about 30% more allowable kinetic energy absorption. The port and captive cushion adjustment valve are located on the same side of cap
The MB series medium duty tie rod cylinder offers an improved design that enhances cylinder operation and ease of use. The standard air cushion utilizes a floating cushion seal to eliminate piston rod bouncing. The cushion volume has been elevated permitting about 30% more allowable kinetic energy absorption. The port and captive cushion adjustment valve are located on the same side of cap
Magnet: None, Mounting: L (Axial Foot), Bore Size: 63mm, Port Thread: Rc, Stroke: 100mm, Rod Boot: None, Lock Style: RN (Rod Side Lock/Non-locking)
Magnet: None, Mounting: Axial Foot, Bore Size: 63mm, Port Thread: Rc, Stroke: 100mm, Rod Boot: None, Lock Style: Rod Side Lock/Non-locking, Auto Switch: -, Lead Wire or Prewired Connector: -, Number: -
Air cylinder series CA2 has been introduced with specifications and dimensions equivalent to the existing CA1 series. Several improvements have been made to the CA2 series including lateral load improvement, increase in cushioning capacity and adoption of?a new cushion seal. There has been enhanced efficiency in handling for cushion valve adjustment, and weight has been reduced by 5 to 15%
This is a legacy product. Please contact us for the latest version.sales@ocaire.com