Serial Network Decentralized Connection A multi-endpoint connection in which data sent by any entity associated with a connection-endpoint is received by all other entities.
The transfer work over the recommended work load may cause the vacuum pressure to decrease by the air leak. The work load shown above is the value when the vacuum pressure reaches 85 kPa, and that is calculated by multiplying the theoretical value by a safety factor of 1/4 for the horizontal lifting or 1/8 for the vertical lifting.
Note 2) Set the pilot pressure by 0.05 MPa or larger than the required maximum set pressrue.
Air can be supplied to or exhausted from the cylinder head side by providing by-pass piping. Maintains a clamped or unclamped state when air supply pressure drops or residual pressure is released.
4 Ff = D x P Formula (3) Load type With small inertial force With large inertial force Load factor 60 to 80% 25 to 35% Formula (4) Ff = (D d) x P OUT IN Series CH2E/CH2F/CH2G/CH2H Theoretical Output Unit: N Operating pressure (MPa) Operating direction Bore size (mm) Rod size (mm) Piston area (mm) 1.0 3.5 5.0 7.0 10 14 804 804 2813 4019 5627 8038 11254 OUT 32 18 550 550 1923 2748 3847 5495
This function prevents such momentary drops from being detected as abnormal pressures by changing the response time setting. P1 P2 Set value
In this region, as a rule, operate the cylinder by providing a guide along the direction of movement. The below table shows the applicable maximum stroke (in cm units), found by calculation assuming the case where the force generated by the cylinder itself acts as buckling force on the piston rod, or piston rod and cylinder tube.
With flow rate adjustment & by-pass Valve type VX2 0 1 2 N.C.
Then, port P and port A are connected. At this time, there will be gaps between the armature t and the core y, but the armature will be magnetically attracted to the core y. Air flow direction: Port P Port A , Port R Block Component Parts Operation principle
The system which realizes wiring saving and distributed installation by connecting to PROFIBUS DP. The signal to PROFIBUS DP is transmitted by GW unit, and the signal to input/output device which is installed discretely is collected by GW unit. 5 6 FG terminal Used for grounding. 7 Mounting hole Used when an unit is mounted with two M4 screws.
END 14-9-2 3 Booster Regulator Series VBA1110 to 4200 VBA1110 VBA1 VBA200, 400 Flow Characteristics Flow Characteristics Flow Characteristics 1.0 0.9 0.8 Outlet pressure (MPa) Outlet pressure (MPa) Outlet pressure (MPa) 0.7 0.6 P1=P =P2 P1=P =P2 P1=P2 P1=P2 0.5 F.R.L.
P K K 8 U 57 (at knob locked) DIN rail part no.
Mount it by referring to external dimensions on page 4-7-38.
Consult with your P/A sales representative. Note 3) Stroke will be reduced by 0.06" for rubber bumper type. *Combination of body options (CM) is available. Note 1) With switch is available on strokes 025(1/4") and greater.
(port e)] [P (port c)] A A LW Plug Operating direction P (port a) P (port b) Auto switch mounting groove [P (port g)] 0.5 Note 2) 0.5 Note 2) Left Right Plug [P (port h)] HI HP H HL HG HT HS HB HA HB HA HG HT HI WB 4-J Depth JK Plug [P (port f)] WB WA TA TA WA R TB Plug TB R W [P (port d)] Inner cover Note 3) holding screw (mm) K 21 20 JK 10 12 J M6 x 1 M10 x 1.5 HT 19.5 39 HS 27 49.5 HP
Actuation Plug Plug (A) 4 (B) (2) Number of solenoids (A) (4) (B) 2 Single 5 (EA) 1 (P) 3 (EB) 5 (EA) 1 (P) 3 (EB) Plug Plug (A) (4) (B) 2 (A) 4 (B) (2) Manual Override Operation Double Warning 5 (EA) 1 (P) 3 (EB) 5 (EA) 1 (P) 3 (EB) Light/Surge Voltage Suppressor Handle carefully, as connected equipment can be actuated through manual override operation.
Elbow type Bulkhead type Click Straight type Low leakage seal construction Reliable sealing is achieved by surface contact. Sleeve lock mechanism Prevents accidents caused by unexpected separation. Lock 1 S Couplers Series KK Variations Plug (P) Socket (S) Male thread type Male thread type Body size Part no. Body size Port size Part no.
rectifying circuit (AC) AC/DC switchover is possible by simply changing the coil.
A 107 110 134 H 63.2 69.2 81.3 B 39 42 53 C 70 75 90 D 22 21 26 E 58 65 76 F 44 50 61 G 36 44 54 Model VHS4510 VHS4510-06 VHS5510 1941 Residual Pressure Relief 3 Port Hand Valve VHS400/500 Model Right 1(P) Left 1(P) Series VHS is a safety manual switching valve for preventing accidents that can be caused by the residual pressure while performing maintenance service on a pneumatic system.