ISG Refer to pages 16-14-3 to 16-14-4 for Safety Instructions and Common Precautions on the products mentioned in this catalog, and refer to pages 16-1-11 to 16-113 for Precautions on every series. q u w e 1 3 LOW i o 2 4 r Selection !0 t Caution !1 1. Select the model taking into consideration the material suitable for the operating fluid.
(Type B) VCW 20 1 G Lead wire length Series 300 mm 600 mm 1000 mm 1500 mm 3000 mm Nil L1 L2 L3 L4 20 30 40 Class 2 Class 3 Class 4 Clip Voltage Electrical entry 1 2 3 4 5 6 36 Flat head screwdriver 100 VAC 200 VAC 110 VAC 220 VAC 24 VDC 12 VDC 230 VAC G D DL DO C T TL Grommet DIN terminal DIN terminal with light DIN terminal (without connector) Conduit Conduit terminal Courtesy of Steven
. * Refer to page 14 for procedures for changing the stopper bolt and switch positions and for top cover replacement instructions.
Do not apply external force to the coil section. When tightening is performed, apply a wrench or other tool to the outside of the piping connection parts. 2. Do not warm the coil assembly with a heat insulator, etc. Use tape, heaters, etc., for freeze prevention on the piping and body only. They can cause the coil to burn out. 3.
Do not service machinery/equipment or attempt to remove component until safety is confirmed. 1) Inspection and maintenance of machinery/equipment should only be performed after confirmation of safe locked-out control positions. 4-17-4
Function plate (With gasket) Note) DXT152-14-1 Mounting screw NXT013-3 Qty. 1 pc. 2 pcs. A B Note) DXT060-51-13B, DXT152-14-1B are for energizing continuously.
Direction of work piece conveyance RSG-B Adjustable shock absorber stroke type (98 + Stroke) Stroke Adjustment bolt 13.5 Note 6) 14 Note 6) 20 60 24 Note 6) 25 A 4-9 through 110 + Stroke 177 + 2 Strokes 67 + Stroke Approx. B With cancel cap RSG-C Dimensions when equipped with cancel cap are the same as in the drawings above.
Do not dispose this fluid in the environment.
Do not service or attempt to remove product and machinery/ equipment until safety is confirmed. 1. The inspection and maintenance of machinery/equipment should only be performed after measures to prevent falling or runaway of the driven objects have been confirmed. 2.
Note) For other voltages, please contact SMC. 3-12-1 A Series VFN2000N Dimensions (mm) VFN2120N--02 148 19 23 Applicable heavy-duty cord O.D.6 to 8 Pg9 37 24 66.5 57 32 40 14 Pilot EXH. 2-5.5 Mounting hole 3-1/4 3 4 5 1 Manual override (Non-locking) 23 23 VFN2220N--02 224.5 19 23 Applicable heavy-duty cord O.D.6 to 8 Pg9 24 66.5 57 32 40 14 Pilot EXH. 2-5.5 Mounting hole 189 3-1/4 3 4 5 1
Do not connect the earth to a water pipe, a gas pipe, or a lightening rod. Do not plug too many leads into a single socket. That causes exothermic heat or fire.
Do not connect the earth to a water pipe, a gas pipe, or a lightening rod. Do not plug too many leads into a single socket. That causes exothermic heat or fire. Do not modify the internal electrical wiring of the product. 10.2 Specifications An earth leakage breaker is installed in the product.
Do not drop or bump. Do not drop, bump, or apply excessive impacts (300m/s2 or more for reed switches and 1000m/s2 or more for solid state switches) while handling. Although the body of the switch may not be damaged, the inside of the switch could be damaged and cause a malfunction. 5. Do not allow short circuiting of loads.
Do not use in direct sunlight. 8. Do not mount the product in locations where it is exposed to radiant heat. 9. Take appropriate measures against the lightning surge on the equipment side as the auto switches do not have any lightning surge resistance specified in the CE marking. Caution 1.
Do not operate in locations having an atmosphere of corrosive gases, chemicals, sea water, water or steam, or where there will be contact with the same. 2. Do not operate in locations having an explosive atmosphere. 3. Do not operate in locations where vibration or impact occurs. Confirm the specifications for each series. 4.
Do not put the heavy objects on the products. Do not use the products as scaffold. 2. Do not use the products in conditions that do not meet the product specifications. Product Returns When returning the product to SMC, make sure to properly purge to remove all hazardous materials and return the product complying with SMC specified procedures.
Do not touch the LCD indicator. Do not touch the LCD indicator face of the pressure switch during operation. Static electricity can change the readout. 3. Pressure port Do not introduce wire, needles, or similar objects to the pressure port as this may damage the pressure sensor and cause malfunctions. Maintenance Caution Wiring 1.
2 14 13 16 7 14 21 10 to 50 RC(PT)1/8 Refer to p.2.3-18 for details rod end nut and optional bracket.
Example) Full length dimension = A + Stroke = ( + Stroke) + Stroke Bore size (mm) I Q S U Z J C K D L E M H N O 32 M8 x 1.25 60 9 depth 7 12.5 58.5 31.5 14 4.5 13 14 16 7 45 34 5.5 40 M8 x 1.25 69 14 9 depth 7 14 66 35 5 13 14 16 7 52 40 5.5 50 86 19 14 80 41 11 depth 8 7 15 17 20 8 64 50 6.6 M10 x 1.5 7-6-38 39 Series CQ2W/CDQ2W Compact Cylinder: Standard Type Double Acting, Double Rod Foot
Do not put the heavy objects on the products. Do not use the products as scaffold. 2. Do not use the products in conditions that do not meet the product specifications. Product Returns When returning the product to SMC, make sure to properly purge to remove all hazardous materials and return the product complying with SMC specified procedures.