EXxx-OMC0002 . : Standard wiring on the manifold is for double-solenoid valves and output number starts A side and B side in that order. If the mounted valves are single solenoid valves, the output on B side will be empty. (Refer to Figure a.) : Special wiring specification with a mixed wiring of single solenoid and double solenoid can be specified with a wiring specification sheet.
We guarantee that the product will operate normally if it is installed under maintenance and control in accordance with the Operation Manual, and operated under the conditions specified in the catalog or contracted separately. b. We guarantee that the product does not have any defects in components, materials or assembly. c.
A B C D E F G H LAT3-10 10 49 4 60 50 4 10.5 LAT3-20 20 69 6 25 90 80 14 20.5 LAT3-30 30 89 6 25 120 110 24 30.5 13 - LAT3-50 Note 1) Refer to Mounting screw specifications and tightening torques in section 4.3 Mounting (P.24). Note 2) The length of the part of the dowel pin inserted into the positioning hole should be shorter than the specified depth.
Mounting by bracket Mount the fitting between the bracket assembly and bracket B. Then, mount it on the panel precisely by using M6 screws to prevent shrinkage and play.
The external temperature sensor needs to be prepared separately by the customer. 11 Temperature Alarm b contact 5 Do not use in an explosive atmosphere. Do not mount the product in a location where it can be exposed to (CLOSE During Alarm) RTD wiring 12-14 Unused prolonged sunlight.
Construction 6 For CDJ2B6-*Z-B For CDJ2B10&16-*Z-B Fig. 4 Standard product: Double acting/single rod No.
. : Standard wiring of the manifold is for double-solenoid valves and the output number starts at the A side and then B side in that order as shown in the figure a.
Auto switches / Proper mounting position for stroke end detection A B Proper mounting position (mm) Bore size A B 40 63 100 32.5 0 16 0 27.5 0 Note) The above mentioned values are indicated as a guide for auto switch mounting position for stroke end detection.
DRail mounting Direct mounting 20D-A7H/A80H D-A73C/A80C D-F7BAL/F7BAVL D-F7/J79 D-F7V/J79C D-F7W/F79F D-F7WV D-J79W D-M9 D-M9V D-F9W D-F9WV D-F9BA D-A7/A80 D-A79W D-A9 D-A9V Bore size (mm) A 9 13 11 13.5 B 6 8.5 11.5 14.5 A 9.5 13.5 11.5 14 B 6.5 9 12 15 A 6.5 10.5 8.5 11 B 3.5 6 9 12 C 8 12 10 12.5 D 5 7.5 10.5 13.5 C 12 16 14 16.5 D 9 11.5 14.5 17.5 C 11 15 13 15.5 D 8 10.5 13.5 16.5 32
2 M4 x 0.7 x 8 Nickel plated JIS B 2805 Nominal 6 Chromated Cross-recessed head cap screw E type snap ring Handle Ring Lock nut Needle O-ring Chromated Chromated JIS B 2401 P12 Replacement Parts No. Description Material Parts no. Valve Spring Seal NBR, Stainless steel o !0 !
DRail mounting Direct mounting 20D-A7H/A80H D-A73C/A80C D-F7BAL/F7BAVL D-F7/J79 D-F7V/J79C D-F7W/F79F D-F7WV D-J79W D-M9 D-M9V D-F9W D-F9WV D-F9BA D-A7/A80 D-A79W D-A9 D-A9V Bore size (mm) D 8 10.5 13.5 16.5 C 11 15 13 15.5 D 9 11.5 14.5 17.5 C 12 16 14 16.5 D 5 7.5 10.5 13.5 C 8 12 10 12.5 B 3.5 6 9 12 A 6.5 10.5 8.5 11 B 6.5 9 12 15 A 9.5 13.5 11.5 14 B 6 8.5 11.5 14.5 A 9 13 11 13.5 32
Data B Combination of converter and valve unit/Operating purpose Without control valve Throttle valve Flow control valve (With pressure compensation) Operating purpose Control valve Combined valve In case only speed control is needed. Without stop valve Cautions of Selection Without skip valve qMake sure to select a cylinder and a rotary actuator for an air-hydro operation.
Note 2) JIS B 8370: General Rules for Pneumatic Equipment Warning 1. The compatibility of pneumatic equipment is the responsibility of the person who designs the pneumatic system or decides its specifications.
IN OUT Model Port size D C B A 30 30 23.5 14 M5 x 0.8 SRP111-M5 40 40 22.5 15 Rc 1/8 SRP111-01 C D 3 Series SRP Safety Instructions These safety instructions are intended to prevent a hazardous situation and/or equipment damage.
Note 1) ISO 4414: Pneumatic fluid power -Recommendations for the application of equipment to transmission and control systems Note 2) JIS B 8370: General Rules for Pneumatic Equipment Warning 1. The compatibility of pneumatic equipment is the responsibility of the person who designs the pneumatic system or decides its specifications.
IN OUT Model Port size D C B A 30 30 23.5 14 M5 x 0.8 SRP111-M5 40 40 22.5 15 Rc 1/8 SRP111-01 C D 3 Series SRP Safety Instructions These safety instructions are intended to prevent a hazardous situation and/or equipment damage.
N.O. 0.4 0.3 0.2 0.1 0.2 0.3 0.4 0.5 0.6 Operating pressure (MPa) Flow Characteristics/Weight C [dm 3/(s bar)] b Cv C [dm 3/(s bar)] b Cv 1 2 (P A) 2 3 (A R) Valve model Flow characteristics Weight (g) Effective area (mm2) Pilot port size Type of actuation Port size SYJA312-M3 SYJA322-M3 SYJA314-M5 0.41 0.18 0.086 0.35 0.33 0.086 Body ported N.C. N.O. N.C.
.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com VR Model VH Flow characteristics (2) 1 4/2 (P A/B) 4/2 5/3 (A/B EA/EB) C [dm3/(sbar)] Cv Type of actuation Port size Pilot port size b Cv b C [dm3/(sbar)] Valve model Pilot VHS Body ported Body ported Base mounted Base mounted (With sub-plate) VZA212
Connection thread R Applicable tubing Bracket mounting dimensions B S (Width across flats) Weight (g) O. D.
N.O. 0.1 0.2 0.3 0.4 0.5 0.6 Operating pressure MPa Flow Characteristics/Mass Flow characteristics C [dm 3/(s bar)] b Cv C [dm 3/(s bar)] b Cv 12 (PA) 23 (AR) Valve model Mass (g) Pilot port size Type of actuation Port size SYJA512-M5 SYJA522-M5 0.12 0.18 0.39 0.45 0.47 0.66 0.14 0.18 0.45 0.45 N.C. 0.53 0.66 M5 x 0.8 Body ported 34 N.O.