Compact Cylinder with Air Cushion Series RQ 8 9 28 7 57 14 1/8 31.5 8 71 19 11 1/4 Refer to page 784 for details on rod end nut and accessories.
<* 1 LVA Orifice size 1 2 3 4 5 6 77 6 6 0 6 LVH Rated voltage 1 2 3 4 7 8 ,, 9= 5,'., ?
Also, keep the manual where it can be referred to as necessary. 1/8 3 to 5 1/4 8 to12 3/8 15 to 20 1/2 20 to 25 2) If the fitting is tightened with excessive torque, a large amount of sealant will seep out. Remove the excess sealant. 3) Insufficient tightening may cause seal failure or loosen the threads. 4) For reuse 2. Ensure sufficient space for maintenance activities.
Model AM850 AM250 AM350 AM450 AM550 AM650 AM150 Rated flow (l/min (ANR)) 750 1500 2200 3500 6000 12000 300 (1) Port size (Nominal size B) 1/8 ,1/4 ,3/8 1/4 ,3/8 ,1/2 3/8 ,1/2 ,3/4 1/2 ,3/4 ,1 3/4 , 1 1, 11/2 11/2 , 2 0.38 0.55 0.9 1.4 2.1 4.2 10.5 Weight (kg) Note 1) Max. flow capacity at a pressure of 0.7MPa. It varies depending on operating pressure.
IR2000 : G43-2-01 G43-P2-N01-X30 IR2010 : G43-4-01 G43-P4-N01-X30 IR2020 : G43-10-01 G43-P10-N01-X30 Port size 02 : 1/4 Note4) Set pressure Thread type NIL:Rc N:NPT 0: 0.005~0.2MPa 1: 0.01~0.4MPa 2: 0.01~0.8MPa F:G (Note 3) The pressure gauge is not attached and becomes bundled shipment. (Note 4) One type only. 4. Marking on product Product name plate MAX.SUP.PRESS. MAX.SUP.PRESS.
F.G. 4. 1. 1. 2. 12 10N [102kgfcm] 1. 2032 20N [204kgfcm] () 40,50,63 30N [306kgfcm] 2. 3. 2. 1.52 1. 2. 1. 1()ISO VG32 3. 4. 5. 6. 1. 2.14.5mT CE1 3. 4. (DC1224V) [] 1. 2. 3. 4. 2.
Dynamic moment Me3 L2 We W = 1/3 14.7 (50 + 27) 103 Review Me3. = 0.38 [Nm] 3 = Me3/Me3 max = 0.38/3 = 0.13 Guide central axis A Me1 W We Me1 = 1/3 We (L1 + B) 103 = 1/3 14.7 (50 + 48) 103 L1 B = 0.48 [Nm] 4 = Me1 /Me1 max = 0.48/3 = 0.16 Review Me1.
Select a filtration rating of 5 m or below, or that equivalent to or lower than ISO 8573-1:2010 [6:4:4] * This rating is equivalent to the rating produced when an air filter is installed for the purity class [7:4:4] of the inlet side compressed air. according to the procedures indicated in the operation manual.
Mounting Warning 1. Operation Manual (this document) In the case of diodes, the residual voltage is approximately 1 V. 4.
Pin Remarks LED indicators 1 Switch cover IP65 rating to IEC 60529 (IP rating is outside range UL/cUL certified) Protection class Yellow ON Transmission or reception of Ethernet telegrams on Port 1/2 (XF1/2) 1 24 V (US1) Safe input connection 4 x M12, 5-way sockets 1 2 3 4 5 LED indicators 2 Yellow OFF No transmission or reception of Ethernet telegrams on Port 1/2 (XF1/2) 2 0 V (US1) Withstand
1 1 2 5 2-1. 5 2-2. 5 2-2-1. 5 2-2-2. 5 2-2-3. 6 2-3. 6 3 3-1. 7 3-2. 7 4 4-1. 8 4-2. 8 4-3. 8 5 5-1. 9 5-2. 10 5-3. 10 6 6-1. 11 6-2. 12 CEP1B12 13 CEP1B20 14 , 1 ,, , ,ISO4412 *1)JIS B8370 *2) ,, , ,, *1) ISO 4414 Pneumatic fluid power-Recommendations for the application of equipment to transmission and control systems. *2) JIS B8370
Chamfer dimension D[mm] Recommended value Connection thread size Rc NPT G 1/8 10.210.4 10.510.7 9.810.2 1/4 13.613.8 14.114.3 13.313.7 3/8 17.117.3 17.417.6 16.817.2 1/2 21.421.6 21.721.9 21.021.4 Tightening method First, tighten it by hand, then give it an additional 1/6 turn to 1/4 turn with a wrench. Refer to the table below for reference values.
When 1 digit = 1 kPa, the pressure is given with an increment of Digit (Min. setting unit) 1 kPa, e.g., 1, 2, 3,, 99, 100. E Energy saving automatic control Indicate that the vacuum pressure during adsorption is monitored and ON and OFF of the ejector is automatically controlled.
Maximum operating pressure 125 psig (0.9 MPa) Size Port AZ3 AZ4 Connections Code 2P 542 2P 2PW 2PW 1/4 inch face seal (Male) 1) 1/4 inch face seal (Female) 1/4 inch tube weld 3/8 inch face seal (Male) 1) 3/8 inch face seal (Female) 3/8 inch tube weld 1/2 inch tube weld MV4 FV4 TW4 MV6 FV6 TW6 TW8 Material Body material 316L SS Code S Ports Code Ports Connection Machined Welded 2P 2PW
For compressed air quality, refer to SMCs Best Pneumatics catalog. 1. The solenoid valve is an electrical product. For Warning safety, install an appropriate fuse and circuit breaker before use. 1. Polarity Caution 4. Use clean air.
time selections with anti-chattering function: 20ms, 160ms, 640ms, 1280ms) With short circuit protection 0.2% F.S. 2 digits or less 0.2% F.S. 1 digit or less Short circuit protection Repeatability Note 2) Output voltage: 1 to 5V 2.5% F.S. or less (with rated pressure range) Linearity: 1% F.S. or less; Output impedance: Approx. 1k Output current: 4 to 20mA; 2.5% F.S. or less (with rated pressure
When 1 digit = 1 kPa, the pressure is given with an increment of Digit (Min. setting unit) 1 kPa, e.g., 1, 2, 3,, 99, 100. E Energy saving automatic control Indicate that the vacuum pressure during adsorption is monitored and ON and OFF of the ejector is automatically controlled.
Disassembly Procedure 1) Loosen hexagon socket head cap screw 1 so that bonnet 2, spring 3 and diaphragm Ass'y 4 are disassembled. 7.2.2. Assembly Procedure 1) Assemble crimped side of diaphragm Ass'y 4 (white resin part) to face body side.
The indicator light The catch sensor Refer to The switch output is (green 1 or green reference No.1 does not operate on 1+2) remains on. normally The indicator light The product is (red) remains on broken or all indicator Yes lights remain off No Refer to reference No.2 The indicator light (green 1 or green The switch output is The product is 1+2) remains on off broken The indication Refer