Rodless Cylinder for Vacuum Series CYV ø15, ø32 To determine whether or not the cylinder can be operated, do not allow the sum (n) of the load factors (n ) for each mass and moment to exceed "1". n = Load mass (m) Max. load mass (m max) + Static moment (M) Allowable static moment (M max) + Dynamic moment (Me) Allowable dynamic moment (Me max) 1 Moment Load mass Max. load mass (Static moment/Dynamic moment) Allowable moment (kg) m M3 m
Basic weight Size 22.5 Single vane 162 90 1 Positioning pin hole 25 161 180 261.5 90 Adjustment bolt (A) Adjustment bolt (B) 3 30 259.5 180 For 90 rotation Single vane (S): 80 to 100 adjustable 440 90 7 50 436 180 675 90 20 Adjustment bolt (A) adjustment range Adjustment bolt (B) adjustment range 60 670.5 180 180 Allowable Loads Do not permit the load and moment applied to the table to exceed
Main switch circuit OUT Black [White] OUT Black [White] DC () Blue [Black] DC () Blue [Black] Indicator light D-Y7BW(V) D-Y59B, Y69B ON OUT (+) Brown [Red] OUT (+) Brown [Red] Operating range OFF Red Indication Green Red Optimum operating position OUT () Blue [Black] OUT () Blue [Black] Contact Protection Boxes/CD-P1 1, CD-P12
(Do not use machine oil or spindle oil ) When bottom mounting, the guide shaft will protrude from the bottom surface Therefore' drill a hole lor a hexagon-holed bolt for mounting and an escape hole for guide shaft on the mounting surface.
Mounting types Cylinder option Bore size B L F T U Basic type Axial foot type Front flange type Center trunnion type Front trunnion type Nil N R H Both sides Without cushion With front cushion With rear cushion 40 50 63 80 100 40mm 50mm 63mm 80mm 100mm Aluminum tube Cushion Part nos. for cylinders with built-in magnets In the case of cylinders with built-in magnets but no auto switches, do
Do not use two cylinders facing one another horizontally or vertically in such a way that their piston rods strike each other. 7. When the cylinder head side contains hydraulic fluid or is in a normally pressurized condition, the applied load must not be allowed to strike the piston rod end. Avoid such applications. 8.
Note 2) 10 to 60C Ambient temperature Enclosure IEC529 Standard IP67, Immersible construction (JIS C 0920) Contact Protection Box: CD-P11, CD-P12 Lead Wire Length
Do not rotate the cover. Rotating the cover when mounting the cylinder or screwing pipe fittings into the ports may cause damage from the cover joint section. 1. Grease packs Order grease for maintenance using the order number below. Grease pack GR-X-005 (5g) Caution 1. Be careful of the snap ring springing out.
resistance 50 M or more at 500 VDC Mega (between lead wire and case) Insulation resistance Withstand voltage 1000 VAC for 1 minute (between lead wire and case) 10 to 60C Ambient temperature Enclosure IEC529 standard IP67, JISC0920 waterproof construction Contact Protection Boxes: CD-P11, CD-P12 Lead wire length
Note) When two L250 elements are used, do not discard the intermediate holder and lower element holder attached under the element, since they are reused. (Made to order elements) c Align the indentations of the case with the projections of the cover, lift the case upward by about 10mm and rotate it clockwise about 20 degrees.
Please do not attach the switch with any other screws than those already attached to the auto switch body. The operation range is shorter than that of the conventional models. If the auto switch replaces the conventional model, it may not function depending on its application because the operation range is shorter. Refer to the examples below.
At this time, take sufficient precautions since the table may move if an external force is applied. 2) Do not conduct inspection while the actuator is in operation. If inspection is unavoidable, it must never take place within the operating range of the actuator. 3) If any abnormality is found in periodic inspection, consult P/A immediately.
Provide support so that the TSUBAKI CABLEVEYOR and parts do not move freely. 2. Implement protective measures (safety cover, etc.). 3. Be sure to turn off the power and ensure that it cannot be turned on accidentally before installation, removal or maintenance of the equipment. 4.
Height tolerance Width Height Parallelism Symmetric type standardized Available with all options MXQ12-30 MXS12-30 86 0.08 46 30 0.035 80 0.2 50 32 0.2 Wide variety of adjuster options Body mounting through holes Positioning pin holes Auto switch mounting grooves Improved work piece mounting repeatability Auto switches can be mounted in grooves provided on the side of the body where they do
10,20,30,40,50,75,100,125,150 10,20,30,40,50,75,100,125,150 Stroke adjuster/shock absorber option BS BT With shock absorber at extension end* With shock absorber at retraction end* *Shock absorber option is not available for MXS6 52 Air Slide Table MXS Series Construction/Parts list, Seal list 3 6 8 9 br bs bt bp 7 2 1 bl bk bq 4 bm bn bo 5 ck cp cm cn co cq cs cr ct dk dp dn em en dr dt ek dm dq dl do
$dem B,/Bltr{ing air ft parb clebnim aDe\rv pctnt: -58'F c. less (Atnospheric pressure) aEfficiency: Lessthan 100pa icles 0.3microfts o( larger per cubic loot. allote; Use of Clean gas filter (lvernlrane) in do/(/tlstearn lin-. ,s rccommerxleo. Distributed by: ?svE' Silrc Pneumatics Inc. 301'l N. Franklin Rd. . P.O. Box 26640 . Indianapolis, lN 46226 Phone: 317-899-4440 .
Olf a lubricant is used in the system, use turbine oil type f 1 (lSO VG32). lf lubricant has been used in the system, do not cease to lubricate as the original lubricant applied during manutacturing will have been washed away.
Lubrication aTh yah,e h8 bon lub,ric.td ior ltb d nrlnubcfrirE. and dor noa lqoirr fudfiar fubdcdion in svba. ef a lubricant is used in the system, use turbine oil type #1 (lSO VG32). lf lubricant has been used in the system, do not cease to lubricate, as the original lubricant applied during manuiacturing will have been washed away. See table of suggested lubricants.
swirches Pfessrre to the side irdicated by label B rotales the shaft clockwise, pressu to the side hbeled A rciates the shaft countercl@kwise, l{cnAtB\lv3o l,rcRAroso--10() o Series:NCRAl Shaft Load fr"u lvlc&l direclion Fsa Fsb $cRAAUrgt 6 cnAtaso 110 44 44 NcRAlffl 132 44 ffi NCf,Ant8() 198 44 NCnA1otOO 220 44 In the stop position, the load can meet the value given in lhe list, please do
Not 3) Aor3 6 15 (basic typ) ar tully pod6d and do not rqunettl x150 optton. Specifications