VHS Chromated C3604B Piston C3604B Spring holder Zinc chromate SWP Parallel pin Zinc chromate SWPB Spring SUS304W Valve spring PVC Packing w Do not remove the retaining screw of the handle. If the screw falls off, it could lead to a malfunction.
How to Order Do not replace heavy duty scrapers. XC4 Since heavy duty scrapers are press-fit, do not replace the cover only, but rather the entire rod cover assembly. The CM2 series cannot replace either heavy duty scraper or rod seal. (It goes for replacing retainer assembly for the CS1 series.) Replace the CNA2 series with the lock unit.
Model (Standard) Dimensions Pressure range (1) Connection thread Indication unit Model G15 MPa MPa G15-10-01 (2) R 1/8, M5 (Female thread) 0 to 1.0 0 to 1.0 1 16 G27-10-R1 R MPa Note 1) Do not apply more excessive pressure than max. pressure display. It will be a cause of malfunction.
Because suctioned matter is ejected together with exhaust, do not direct an exhaust port at a person or equipment. AFJ AMV 2.
Note 1) Do not use the power supply of inrush current prevention type for the controller power supply. When conformity to UL is required, the electric actuator and controller should be used with a UL1310 Class 2 power supply. 560
Do not replace the bushings. The bushings are press-fit. To replace them, they must be replaced together with the cover assembly. 2. To replace a seal, apply grease to the new seal before installing it. If the cylinder is put into operation without applying grease to the seal, it could cause the seal to wear significantly, leading to premature air leakage. 3.
Do the drain pulling out regularly.
Do not replace the non-rotating guide. Since the non-rotating guide is press fitted, the entire cover assembly needs be replaced instead of a single part. 37
Do not replace the non-rotating guide. Since the non-rotating guide is press fitted, the entire cover assembly needs be replaced instead of a single part. 38
You do not need to specify "N" (i.e., without lead wire) for D-A3A, D-A44A, D-G39A, and D-K39A. This is the only standard specification automatically available for these models.
low speed actuation (no control of cylinder output) Example 2) Low speed with output control Precision restrictors Solenoid valve ITV (Electro-pneumatic regulator) Mist separator (0.01 m or less) (0.3 m or less) Mist separator (0.3 m or less) Air filter (5 m or less) IR (Precision regulator) W Air filter (5 m or less) IR (Precision regulator) W When performing control of cylinder output, do
Do not replace the non-rotating guide. Since the non-rotating guide is press fitted, the entire cover assembly needs be replaced instead of a single part. 37
Do not replace the non-rotating guide. Since the non-rotating guide is press fitted, the entire cover assembly needs be replaced instead of a single part. 38
Do not replace the bushings. The bushings are press-fit. To replace them, they must be replaced together with the cover assembly. 2. To replace a seal, apply grease to the new seal before installing it. If the cylinder is put into operation without applying grease to the seal, it could cause the seal to wear significantly, leading to premature air leakage. 3.
Do not disassemble the power clamp cylinder. The power clamp cylinder consists of a completely sealed structure in order to protect it from welding spatter. Do not disassemble, except for when replacing any of the replaceable parts, as the performance may deteriorate. 10 Power Clamp Cylinder Variations Web Catalog.
VQC4000/5000 series valves do not have common polarity.
② For manifolds with serial transmission kits, whether the valves are positive common or negative common depends on the type of protocol. For VQC1000/2000 series valves, install valves with the same common specification as the common specification of your protocol.
Do not restrict the flow rate by plugging or mounting a speed controller to the exhaust port.
In addition, SY7120 series valves do not come with a gasket because they are the equivalent of existing SY7000 series body ported valves.
The SY7000 series body ported valve gasket assembly part number is “SY7000-GS-1.”
Do not tighten or loosen the release bolts excessively. Also, do not tighten them with a pneumatic or electric screwdriver because it may damage internal parts of the product.
For further details, refer to the excerpts from the MWB series “Specific Product Precautions” below.
However, unlike KS and KX series rotary One-touch fittings, they do not rotate with low friction. Do not use the product in a manner in which the connected tube swings or rotates with respect to the fitting.