VS 8-2/VS 8-4

Mounting screw (M4) Terminal block cover M3 screw Gasket 6 mm Electrical entry 2 x G 3/4 Step 3. Mounting the terminal block cover Securely tighten the screws to the torque shown below, after confirming that the gasket is installed correctly.

Compact

A LEC SS-T LEC Y Model Screw size Maximum tightening torque [Nm] A [mm] L [mm] LEMBl M5 3 5.5 24.5 LEMC25 LEMH25 M3 0.6 3.4 23.7 2. Never hit at the stroke end except during return to origin. (Except when the LECP2 controller is used.) Internal stopper can be broken.

High Rigidity Slider Type Ball Screw Drive/11-LEJS Series

8 10 10 0 L/min (ANR) ISO Class 7 ISO Class 7 10 10 Particle concentration [particles/m3] Particle concentration [particles/m3] ISO Class 6 ISO Class 6 10 10 0 L/min (ANR) 50 L/min (ANR) ISO Class 5 10 10 ISO Class 5 30 L/min (ANR) 1000 1000 ISO Class 4 ISO Class 4 90 L/min (ANR) 100 100 50 L/min (ANR) 10 10 1 1 0 0.1 0.2 0.3 0.4 0.5 0.6 0 0.1 0.2 0.3 0.4 0.5 0.6 Particle diameter [m] Particle

Speed Controller with

Accessory: Cross Recessed Round Head Screw for Mounting (Zinc chromated) Model Size (Nominal x Length) Piece Metric size Inch size TMH-01J TMH-03J TMH-07J TMH-07 TMH-09 TMH-23J TMH-04J TMH-06J TMH-06 TMH-08 TMH-10 TMH-12 M3 x 15 M3 x 20 1 M4 x 25 M4 x 35 TMH-13 Series Holder mounting Select the applicable holder/TMH for each speed controller from the below table.

EX260-SEN_eng

OFF M3 hexagon screw Tightening torque 0.6 Nm 1 2 0 0 0 IP address 192.168. Y . X : Thread size: M3 x 30 The following instructions must be followed during maintenance: Turn off the power supply. Stop the air supply, exhaust the residual pressure and verify that the air is released before performing maintenance. Otherwise an injury can result.

EX260-SPN-A_eng

Valve manifold Accessories Side D NOTE (SI unit side) Replacement of the SI unit Remove the M3 hexagon screws from the SI unit and release the SI unit from the valve manifold. Replace the SI unit.

EXxx-OMV0018_ENG

Otherwise malfunction can result, causing an accident. : Thread size: M3 x 30 Node ID setting No.1 Reserved Technical documentation giving detailed specification information can be found on the SMC website (URL http://www.smcworld.com). The following instructions must be followed during maintenance: Turn off the power supply.

EX500-Sx03_eng

Check that the M3 hexagon socket head cap screws have been tightened to the specified torque. If these items are not adhered to, it may lead to damage to the unit or intrusion of liquid or dust into the units.

Parallel Type Air Gripper

Model Screw Max. tightening Maximum screw-in depth (L mm) torque (Nm) MHZ2-10 M3 x 0.5 0.9 6 MHZ2-16 M4x0.7 1.6 4.5 MHZ2-20 M5 x 0.8 3.3 8 L L MHZ2-25 M6x1 5.9 10 MHZ2-32 M6x1 5.9 10 MHZ2-40 M8 x 1.25 13.7 13 Model Screw Max. tightening torque (Nm) Maximum screw-in depth (L mm) MHZ2-10 M3 x 0.5 0.69 5 MHZ2-16 M4x0.7 2.1 8 MHZ2-20 M5 x 0.8 4.3 10 MHZ2-25 M6x1 7.3 12 MHZ2-32 M6x1 7.9 13 MHZ2

180 ° Angular Type Air Gripper Rack & Pinion Type MHW2 Series ø 20, ø 25, ø 32, ø 40, ø 50

M3 x 0.5 M4 x 0.7 M5 x 0.8 M6 x 1 Model Applicable bolts Max. tightening torque (Nm) MHY2-10D MHY2-16D MHY2-20D MHY2-25D Model Bore(mm) Hole depth (mm) Attachment MHY2-10D MHY2-16D MHY2-20D MHY2-25D 11H9 17H9 21H9 26H9 1.5 1.5 1.5 1.5 +0.043 0 +0.043 0 +0.052 0 +0.052 0 0.88 2.1 4.3 7.4 M3 x 0.5 M4 x 0.7 M5 x 0.8 M6 x 1 (1) To mount the attachment to the finger, make sure to use a wrench

180

. : MH-G04 (30 g) 706 MHY2 Series 180 Angular Type Air Gripper Cam Type Dimensions MHY2-10D Pin hole positioning 30 9 9 2 x M3 x 0.5 thread depth 4 4 (Thread for mounting attachment) 4 x M3 x 0.5 through (Mounting thread) 3H9+ 0.025 0 depth 3 6 0.005 0.025 4 4 x M3 x 0.5 thread depth 6 3 6 (Mounting thread) 2 x 3.4 through 2 x M3 x 0.5 depth 6 12 (Mounting hole) (Mounting thread) (Limted

Series SYJ700 Rubber seal 3 Port Pilot Solenoid Valve

Prefix it to the part nos. of the solenoid valve, etc. 39 Series SYJ700 Combinations of Solenoid Valve, Manifold Gasket and Manifold Base Blanking Plate Assembly Body ported (Type SYJ72) Base mounted (Type SYJ74) Model no.: SYJ700-10-2A (In common for body ported type and base mounted type) Round head combination screw M3 x 8, Matt nickel plated Round head combination screw M3 x 31, Matt

Compact Electro-pneumatic Regulator Series ITV0000

radius 80 3.4 13 4.5 6 Series ITV0 Dimensions Single unit for manifolds 56 50 PWR ERR M8 x 1 Cable connection threads 15 15 9 84 86 3.7 Breathing hole Note) (M3 x 0.5) OUT OUT port (4, 5/32") 8 2 5 18.5 Note) When used under the conditions equivalent to IP65, use the regulator after piping a fitting/tube into a breathing hole.

VDW Series, Compact Direct Operated 2/3 Port Solenoid Valve for Water and Air

x 0.5 When not equipped with bracket, the M3 threads at both ends (4 positions) can be used for other purposes. (16.3) 11.5 7.7 7.7 11.5 5 22.5 40 7.5 L dimensions n (stations) Dimensions 3 4 6 8 2 9 5 7 10 52.5 L1 70 105 140 35 157.5 87.5 122.5 175 62.5 L2 80 115 150 45 167.5 97.5 132.5 185 69.5 L3 87 122 157 52 174.5 104.5 139.5 192 3 stns. x 1 2 stns. x 2 3 stns. x 2 2 stns. + 3 stns

IDX-OM-M051

M3 tightening torque: 0.63 to 1Nm. Do not touch equipment other than the terminal block during wiring. 3. Put back the front panel. [Remote operation] Voltage is applied to the terminal block. Be sure to turn off the switch with lamp before wiring. 1) Disconnect the wires from no. 5 and 6 of the terminal block and mount the external switch.

IDX-OM-U022

M3 6.5mm 1.25mm 2 M3 6.5mm 1.25mm 2 IDFA100F150F 1 6 1.3 IDX-OM-U022 2. 2.1 45 45 45 IDFA100F150F 2 1 2.1 IDX-OM-U022 2. 2.2 2.2.1 (1) (85%) () B C 245050 () 2000m ) (2) IDFA100F150F 2 2 2.2 IDX-OM-U022 2. 2.2.2 P.6-3 6.3 IDF-AB501 14 1 1 1 4 5 2 3 1 600mm 600mm 600mm 600mm 600mm 1 IDFA100F150F 2 3 2.2 IDX-OM-U022 2. 2.2.3 60 60 .

PSxx-OMT0001CN

m5 m GH641 m3 m5 m 200 kPa ISA3-F ISA3-G 1 m3 m5 m 1 m3 m5 m [mm] [mm] 9 0 10010 ISA3-H 1 m3 m5 m [mm] 29 0 30030 -20No.PS-OMT0001CN-E 2 ISA3-() ISO1179-1 1 2 3 4 5 6 L1 38 76 114 152 190 228 C(4 ) C(6 ) F(G ) H 13 13.6 19 ISA-14() -21No.PS-OMT0001CN-E 2 ISA3-(DIN ) ISO1179-1 1 2 3 4 5 6 L1 38 76 114 152 190 228 L2 62.5 125 162.5 200 237.5 275 L3 73 135.5 173 210.5 248 285.5

EX260-SMJ_eng

M3 hexagon screw Tightening torque 0.6 Nm Terminating resistor Valve manifold : Thread size: M3 x 30 Troubleshooting The following instructions must be followed during maintenance: Turn off the power supply. Stop the air supply, exhaust the residual pressure and verify that the air is released before performing maintenance. Otherwise an injury can result.

F/ISE

Mounting with brackets Mount a bracket to the using two M3 x 5L mounting screws and install on piping with a hexagon socket cap screws. The switch can be installed horizontally depending on the installation location. Mounting screw M3 x 5L Atmospheric release port To a safe place with no water or dust The tightening torque for bracket mounting screw should be 0.98Nm or less.

E-P HYREG ® Series VY1 1

Pressure gauge (Option) G27-10-01 Pilot EXH port AL Silencer (Option) AN120-M5 Rc 1/8 gauge port Foot (Option) VEX1-18-2 Hexagon socket head cap screw M3 =8 (2 pcs.) (With spring washer) ( ) Bracket (Option) VEX1-18-1A 2-4.5 mounting hole Hexagon socket head cap screw M3 =8 (2 pcs.)