(mm) H1 6 7 8 11 11 H 36 40 45 53 56 GY 5 5.5 7 8 10 GX 10 8.5 9 11.5 11.5 EY 26 42 54 64 72 D 12 14 16 20 20 B1 17 19 22 27 27 C 54 68 86 104 124 B 24 28 32 39 50 BY 7 8 9 9 12 AL 19.5 23.5 27 32 32 BX 9 6.5 8 10 11 ET A 22 26 30 35 35 BS 42 50 54 64 63 K 5.5 5.5 6 7 7 BT Model MUB25 MUB32 MUB40 MUB50 MUB63 Standard stroke (mm) 5, 10 5, 10 5, 10, 15, 20 5, 10, 15, 20 5, 10, 15, 20 M5 x 0.8
The allowable load mass and maximum operating pressure should be as shown in the table below. The cushion effect (smooth start-up, soft stop) exists only before the stroke end in the stroke ranges indicated in the table below. The cushion effect (smooth start-up, soft stop) cannot be obtained in an intermediate stop or return from an intermediate stop using an external stopper, etc.
The load factor for each direction can be found as follows. x = 0/400 = 0 y = 50/250 = 0.2 z = 200/1500 = 0.13 5. x + y + z = 0.33 1 1000 1000 1000 Lz 800 800 800 600 600 600 L1 [mm] L3 [mm] L2 [mm] 400 400 400 Lx Ly 200 200 200 0 0 0 0 10 20 30 40 50 60 70 0 10 20 30 40 50 60 70 0 10 20 30 40 50 60 70 Work load [kg] Work load [kg] Work load [kg] 8 LEKFS Series Battery-less Absolute (Step
Throttle speed controller, such as Series AS, is recommended for speed adjustment.
When this is the case, decrease the supply pressure as much as possible or slightly increase the set pressure and restrict the output line (such as by adding a throttle valve to adjust the pressure). Can also be used in an intensive piping system.
If the effective area is smaller, it may encounter an unexpected sudden slide table movement. Install a solenoid valve for braking as close to the cylinder as possible. If there is a long distance between the cylinder and valve, it may cause fluctuations in the stop accuracy or unexpected sudden slide table movements.
If the effective area is smaller, it may encounter an unexpected sudden slide table movement. Install a solenoid valve for braking as close to the cylinder as possible. If there is a long distance between the cylinder and valve, it may cause fluctuations in the stop accuracy or unexpected sudden slide table movements.
FH FH 140 70 HOW 215 42 20 Hexagon socket head cap screw (M6 x 10) 4 pcs. Handling Precautions Mounting q The flat portion of the stainless steel cover functions as the contaminant adsorption surface.
As a guide, refer to the proper tightening torques shown below.
Orifice Fittings Many of our small brass fittings such as B1, B2, T1, T2, etc., are available as orifice fittings. In the case of Tees, the branch and/or one end of the run may be an orifice. A cross can have as many as three orifices. The general dimensions in this catalog are subject to change without notice 5/32 Couplings 7/16 1/2 15/16 1 5/16 5/16 Typ.
Take measures to ensure air quality, such as by installing an aftercooler, air dryer, or water separator. Compressed air that contains a large amount of drainage can cause the malfunction of pneumatic equipment, such as air grippers. Therefore, take appropriate measures to ensure air quality, such as by providing an aftercooler, air dryer, or water separator. 4.
Metal seal structure with low sliding speed and an output control, which Long service life Low & Uniform speed actuation Low & Uniform speed actuation Long service life Smooth, uniform speed actuation ranges as low as 0.3 mm/s. Long service life of 10,000 km or 100 million full cycles.
Operating Range (mm) Bore size Switch types 25 32 20 D-A9, D-A9V D-F9, D-F9V D-F9W, D-F9WV 11 12.5 14 6.5 7 7 Values in this table include hysteresis and are to be used as a guide only. They do not guarantee an actual fixed range (expect approximately 30% dispersion).
25 30 0 5 10 15 20 25 30 Time of water flow (min) Measuring time (min) Test method and conditions The liquid contact portions were filled with sulphuric acid and left untouched for half an hour.
MHL2-10D MHL2-16D MHL2-16D MHL2-10D 2 1 2 1 60 60 25 25 0.6MPa 0.6MPa Holding force (N) Holding force (N) Holding force (N) Holding force (N) 50 50 20 20 0.5MPa 0.6MPa 0.5MPa 0.6MPa 40 40 15 15 0.4MPa 0.5MPa 0.4MPa 0.5MPa 0.4MPa 0.4MPa 30 30 10 10 0.3MPa 20 20 0.3MPa 0.3MPa 0.3MPa 0.2MPa 5 5 10 10 0.2MPa 0.2MPa 0.2MPa 10 20 30 40 50 60 70 20 40 60 80 100 120 20 40 60 80 100 120 0 0 0 10 20
Valve specifications Note 1) Conductance is molecular flow measured with an elbow pipe which has the same dimension as each applicable flange. Note 2) For one cycle of cylinder.
Please contact SMC for use in an environment where the product is exposed to such liquid as cutting oil, lubricant oil or coolant oil. 15-7-12
This is usually achieved by having dual channels of operation, such as dual valves, dual wiring, dual guard switches etc.
Stroke ST (mm) 0 4 6 8 10 15 20 Caution Stroke ST (mm) When driving an inertial load, operate a cylinder with kinetic energy within the allowable value.
An environment where food which will be sold as merchandize, directly touches the fitting components. Installable Splash zone An environment where food which will not be sold as merchandize, directly touches the fitting components. An environment where there is no contact with food.