Smooth Cylinder Series CQSY Smooth Cylinder Minimum 0.01 to 0.03 MPa operating pressure Minimum Minimum 0.01 to 0.03 MPa operating pressure 0.04 Minimum operating pressure MPa 12 16 0.03 20 25 32 40 0.02 50 63 80 100 0.01 0 0 10 20 30 40 60 50 70 80 90 100 Bore size mm (Measurement based on JIS B8377) Series CQSY/CQ2Y/CM2Y/CG1Y/CA2Y 12 to 25 32 to 100 20 to 40 20 to 100 40 to 100 Stable operation possible even at a
Connection Female Thread: Rc, NPT, NPTF Uni thread size Wrench tightening angle after hand-tightening [deg] Tightening torque [Nm] 1/8 30 to 60 3 to 5 1/4 30 to 60 8 to 12 3/8 15 to 45 14 to 16 1/2 15 to 30 20 to 22 Connection thread size Proper tightening torque [Nm] NPT, R1/8 3 to 5 NPT, R1/4 8 to 12 NPT, R3/8 15 to 20 NPT, R1/2 20 to 25 Connection Female Thread: G Chamfered area for female
CBG1N Rubber bumper type CBG1N25-PS Locking at head or rod end CBG1N32-PS CBG1A20-PS 20 25 32 40 CBG1A20-PS CBG1A25-PS CBG1A32-PS CBG1A40-PS Above no. @5, @6, @7, @8, $0, $1. And a grease pack. CBG1A Air cushion type CBG1N40-PS CBG1A25-PS Locking at both ends CBG1A32-PS CBG1N20-PS-W CBG1A40-PS 20 25 32 40 CBG1N20-PS-W CBG1N25-PS-W CBG1N32-PS-W CBG1N40-PS-W Above no. @5, @6, @7, @8.
(The SI unit type is provided for use in Japan.) *6 p: For pipe thread type: NPT only *1 Options B, G, H are not assembled and supplied loose at the time of shipment. *2 Assembly of a bracket and set nuts (AR20-B to AR40-B) Including 2 mounting screws for the AR50-B and AR60-B *3 Mounting thread for pressure gauge: 1/8, Pressure gauge type: G46-20-l *4 For pipe thread type: NPT.
10 to 20 l/min Simple flow setting Without removing the cover, you can set with a screwdriver from the outside.
M4 hexagon socket head cap screw [Replacement Element] END400-005 (5 m Type) END400-020 (20 m Type) 4 elements are required per unit. Protection cover 2-3. Removing cylinder a. Remove the M8 hexagon nut at four parts. b. Remove the cylinder flange holding bolts. Holding bolt: M8 hexagon socket head cap screws at four parts up to the cylinder, and remove it.
M4 hexagon socket head cap screw [Replacement Element] END400-005 (5 m Type) END400-020 (20 m Type) 4 elements are required per unit. Protection cover 2-3. Removing cylinder a. Remove the M8 hexagon nut at four parts. b. Remove the cylinder flange holding bolts. Holding bolt: M8 hexagon socket head cap screws at four parts up to the cylinder, and remove it.
Note that power daisy chaining supports a maximum of 20 MPCs in one power group. This does not mean that you cannot have more than 20 MPCs connected to a single supply. More MPCs can be supported as long as the supply can source enough power to support multiple chains of MPCs. Each MPC uses about 7 watts of power when moving.
Mark C on the unit Mark B at cable end Mark A at cable end (1) (2) (3) End plate bracket (EX600-ZMA2) DIN rail mounting groove 1 Intermediate reinforcing brace (EX600-ZMB2) Intermediate reinforcing brace (EX600-ZMB1) Lock screw: No.4-40 UNC DIN rail 2 End plate bracket (EX600-ZMA2) 5 Connector pin assignment Digital input unit 3 4 3 2 1 1 0 EX600-DX B/DX D EX600-DX C 25 24 23 22 21 20 19
Mount an auto switch at the center of the operating range. In the case of 2-color display auto switch, mount it at the center of the green LED illuminating range. Adjust the mounting position of the auto switch so that the piston stops at the center of the operating range. (The mounting position shown in the catalog indicates the optimum position at stroke end.)
Switching element OFF Resistor Leakage voltage Valve Power supply Leakage current AC coil is 20% or less of rated voltage. DC coil is 3% or less of rated voltage. Selection 2. Low temperature operation Although the valve can be operated at a temperature as low as 0C, measures should be taken to avoid solidification or freezing of drainage and moisture, etc. Warning 1.
L..k.g.: Port to porl (internal) not 1o exceed 0.m7 cubic feet per minule at 100 PSIG (6.9 Kgtcm'). Op.r.Sng Pr..rur..! 28 'Vacuuh to 30o FSIG (20 Kglrcm?).
At least one valve coil has a short circuit, or at least one connected module has a short circuit, or the module layout has changed. Self-test has failed and a power reset is required. An incompatible module is connected to the SI unit.
10 mA (2 V or less at 40 mA) 4V or less 0.8 V or less at 10 mA (2 V or less at 40 mA) Current leakage 0.8mA or less 100A or less at 24 VDC 0.8mA or less 100A or less at 24 VDC Indicator LED Red LED illuminates when turned ON.
(Values at the initial period) Vibration resistance: No malfunction occurred in a one-sweep test between 45 and 2000 Hz. Test was performed at both energized and deenergized states in the axial direction and at the right angles to the main valve and armature.
Too large resistance of In particular, attention should be paid to the piping equipment used and fittings because they are often missed. on the way of Equipment and piping at the exhaust side should piping also be of an appropriate size. Operation at a very low speed can create a The product 1.
20 30 40 Symbol Nil B* H* Symbol 02 03 04 *Note: Bracket and/or panel mount nut are not assembled and are supplied loose at time of shipment.
20 30 40 Symbol Nil B* H* Symbol 02 03 04 *Note: Bracket and/or panel mount nut are not assembled and are supplied loose at time of shipment.
Test was performed at both energized and deenergized states in the axial direction and at the right angles to the main valve and armature.
one end) 1 place Current (Wired) SI unit: 15 units 1 line (Connector at one end) 14 lines (Connector at both ends) 29 places Interchangeability maintained * Maximum I/O of wireless master/ slave unit is limited to 128 points.