SI unit for EtherNet/IP TM Allowable solenoid number by valve series: Keep the number of mounted solenoid valves within specification.
The GSD file of the product depends on the address setting mode (selected by the address setting mode switch).
Fault action Output action at a communication fault can be set by parameter, either Clear Output, Force Output or Hold Last State.
Allowable solenoid number by valve series: Keep the number of mounting solenoid valves within specification.
32 x 2)1 40% 6.6 Increased by Improved by up to times Allowable lateral load Non-rotating accuracy 0.06 0.4 kg 0.1 0.06 kg CXSM10 50 mm stroke (10 x 2)1 JMGPM12 50 mm stroke (10 x 2)1 CXSM32 25 mm stroke (32 x 2)1 JMGPM40 25 mm stroke (32 x 2)1 + m 1 Both cylinders used in the comparison have almost the same piston area.
Value: Q = 0.56 Nl/min. 8.The value of 0.56 Nl/min. is multiplied by 1.4 and by the number of cycles. Q2 = 0.56 Nl/min. 1.4 5 cycles = 3.92 Nl/min.
If any failure occurs due to our fault during the guaranteed period, we will guarantee the non-conformance by delivering a substitute in the worst case. However, responsibility of any damage which is led by the product failure is not taken by us.
Series 16 25 40 Height reduction by 30% MY2C MY2H (Single axis) MY2HT (Double axis) MY1C, MY1H 28 37 58 Low profile achieved by placing the guide unit and cylinder body next to one another.
Allowable solenoid number by valve series: Keep the number of mounted solenoid valves within specification.
L1 [Side mounting] Bore size (mm) Non-rotating accuracy MGPM MGPL MGPA Pin hole 12 16 20 25 32 40 50 63 80 100 0.07 0.05 A 0.06 0.04 0.01 A = Catalog dimension (0.1 + L1 x 0.0008) [mm] 0.05 0.03 : To be 0.15 for 80, 100 Note) Displacement by load and self-weight deflection by plate and guide rod are not included. 0.04 0.03 0.03 0.03 [Bottom mounting] B Pin hole L2 Pin hole B = (0.045
If any failure occurs due to our fault during the guaranteed period, we will guarantee the non-conformance by delivering a substitute in the worst case. However, responsibility of any damage which is led by the product failure is not taken by us.
Allowable solenoid number by valve series: Keep the number of mounted solenoid valves within specification.
Design system to not be affected by water hammer when using water as fluid.
Transfer speed acceleration set range 0.49 to 4.90 m/s 2 (By selection. Please refer to the table below.)
Allowable solenoid number by valve series: Keep the number of mounted solenoid valves within specification.
Eliminate any dust in the transparent cover by blowing air. (Make sure there is no damage of the O-ring.) 4. Insert a new element into the body. 5.
Measurement instruments that SMC manufactures or sells have not been qualified by type approval tests relevant to the metrology (measurement) laws of each country. Therefore, SMC products cannot be used for business or certification ordained by the metrology (measurement) laws of each country. Revision History The PF2M701, 702, and 705 have been added.
-X 20Selection of cylinder used alone Data Change guide type Please refer to information by the guide manufacturer.
Allowable solenoid number by valve series: Keep the number of mounted solenoid valves within specification.
If any failure occurs due to our fault during the guaranteed period, we will guarantee the non-conformance by delivering a substitute in the worst case. However, responsibility of any damage which is led by the product failure is not taken by us.