C76 B A 32 6 7 7 8 40 11 13 12 14 Aim at this number.
Piping and Speed Conrol 1) A single 3-position pressure center solenoid valve or two 3-port solenoid valves are used. (Refer to Figure 1 or Figure 2.) 2) A meter-out-type speed controller is used for ports A and B and a meter-in speed controller is used for ports C and D.
B T Y L Depth ED T 4-LD PA K 4-MM Counter bore depth C Thread depth M F QW PB N A E depth EK Q + Stroke G Z + Stroke Stroke adjustment screw (inner cover) LW A A HP H HL HA HA HI TA TA R 4-J Depth JK Thread depth PC (from counter bore surface) 2-P 2-Counter bore dia.
Caution indicates a hazard with a low level of risk which, if not avoided, could result in minor or moderate injury. Caution: Warning indicates a hazard with a medium level of risk which, if not avoided, could result in death or serious injury. Warning: Danger : Danger indicates a hazard with a high level of risk which, if not avoided, will result in death or serious injury.
If a workpiece is still being held, there is a danger of it being dropped. 7.
Caution indicates a hazard with a low level of risk which, if not avoided, could result in minor or moderate injury. Caution: Warning indicates a hazard with a medium level of risk which, if not avoided, could result in death or serious injury. Warning: Danger : Danger indicates a hazard with a high level of risk which, if not avoided, will result in death or serious injury.
The cylinder should be operated using a connection method which allows for shaft alignment variations and deflection due to the cylinder's own weight. A drawing of a recommended mounting method is shown in Figure 1.
If fingers are caught in a cylinder, there is a danger of injury due to the strong cylinder output, and therefore caution must be Since the connection between the piston rod and table is a floating structure, there is a maximum table backlash of 0.15 mm in the stroke direction. (Refer to the figure below.) 2.
If a workpiece is still being held, there is a danger of it being dropped. 7.
INP 1 INP ON 0.50 2 INP ON a bINP ON < / [mm/sec] [mm/sec] 1 4 30% 1 4 40% 5 20 35% 5 20 60% LEY*16** 21 50 60% 85% LEY*16*A* 21 50 80% 95% 1 4 20% 1 4 40% 5 20 35% 5 20 60% LEY*25** 21 35 50% 65% LEY*25*A* 21 35 80% 95% 1 4 20% 5 20 35% LEY*32** 21 30 60% 85% -41- LEY*16** LEY*25** LEY*32** LEY*16*A* LEY*25*A* A B C A B C A B C A B C A B C [kg] 1 1.5
[ % ] ( ) -32No.PF-OMN0009CN-F () PF3W504 PF3W520 [ M P a ] [ M P a ] PF3W540 PF3W511() [ M P a ] [ M P a ] PF3W521() [ M P a ] -33No.PF-OMN0009CN-F PF3W511(PVC ) PF3W521(PVC ) [ M P a ] [ M P a ] -34No.PF-OMN0009CN-F PF3W504/520/540 PF3W504S/520S/540S [MPa] [MPa] [ M P a ] [ M P a ] a] [MP a] [MP PF3W511() PF3W521() PF3W511/521(PVC ) [MPa] [ M P a ] [ M P a ] a] [MP [MPa
L32 pin clamp cylinder available O Compact design makes it applicable to a broad range of workpieces. OContributes to a lightweight jig.
M5P 3m L M5PL 5m Z M5PZ Side support A Side support B MY-S25A MY-S25B MY-S32A MY-S32B MY-S40A MY-S40B Auto Switch Mounting Bracket Refer to p.4.7-9 for the detailed information on size etc. Cylinder bore size (mm) Mounting bracket Part No.
Z (Ex.) C80CZ Solid state switches marked with a are produced upon receipt of order. 3m. L (Ex.) C80CL None . N (Ex.)
Note 2) O-ring e is included with manifold valve r. 17-2-18 13 Series VCA Direct Operated 2 Port Solenoid Valve For Air Manifold Option Parts Blanking plate assembly (VCA20) VVCA20 4A This is used when a blanking plate is mounted on a manifold as preparation for a planned valve installation.
Contact SMC if a stopper cylinder is to be used for stopping a load that is connected directly to a cylinder, as this will cause the cylinder's thrust to act as a horizontal load.
) 4 3.2 () 5 4 () 24 - No.ZQ-OM01401-B ZS-39-5G ZQ1-LW6-N-A 1) N NPN P PNP (1) 3 Assy ZQ1-PL11-A 4 Assy ZQ1-FC1-A 5 (10 ) ZQ1-FE2-A 6 ZQ1-CV 7 V VVQ1000-50A-C4 (1) 50A-M5 (M5x0.8) (1) 50A-C3 3.2 () 50A-C4 4 () 8 (10 ) 50A-C6 6 () ZK1-CP-A F1-LC3 3.2 () F1-LC4 4 () 9 Assy ZQ1-BK1-A 25 - No.ZQ-OM01401-B 7.3 b a a a 1. (2 ) 2.
Caution indicates a hazard with a low level of risk which, if not avoided, could result in minor or moderate injury. Caution: Warning indicates a hazard with a medium level of risk which, if not avoided, could result in death or serious injury. Warning: Danger : Danger indicates a hazard with a high level of risk which, if not avoided, will result in death or serious injury.
At least one valve coil has a short circuit, or at least one connected module has a short circuit, or the module layout has changed. Self-test has failed and a power reset is required. An incompatible module is connected to the SI unit.
Use a tightening torque of 0.05 to 0.1 Nm. As a rough guide, tighten the screw an additional 90 after feeling a tight resistance. As a rule, it should be turned about 90 beyond the point at which tightening can be felt. 0.5 0.2 0.3 MHL2-20D 0.5 0.2 0.2 MHC MHL2-25D 0.2 0.1 0.2 MHL2-32D 0.4 0.4 0.7 MHT MHL2-40D 0.2 0.4 0.7 MHY MHW MRHQ Misc.