PSE530 Pressure Sensor Series PSE530 How to Order PSE53 0 M5 Sensor range Option None 0 1 2 3 Positive pressure [0 to 1 MPa] Vacuum [0 to 101 kPa] Low pressure [0 to 101 kPa] Compound pressure [101 to 101 kPa] Nil Port size Sensor cable (3 m) M5 R06 R07 M5 x 0.8 6 reducer 1/4 inch reducer L ZSE ISE Option ZSP Connector for pressure sensor controller (1 pc.) + Sensor cable (3 m) Description Part
Port size With One-touch fitting 01 M5 M5 R 1/8 R 1/4 R 3/8 R 1/2 02 03 04 Needle Valve/Flow Rate Characteristics Note) The flow rate characteristics are representative values.
Series AS-FG How to Order AS 1 0 3 2 F G 01 06 Body size M5 standard 1/8, 1/4 standard 3/8 standard 1/2 standard 1 2 3 4 Option Type Nil S None With seal 2 3 Elbow Universal M5 and U10/32 are not available with seal. Control type Applicable tubing O.D.
Series NCY3B Series NCY3B6 Piping port M3 0.12 inch NN Piping port M5
The air catch sensor is IP66-compliant, but when there is a possibility of water, oil, etc. from the exhaust port entering the case interior, use an M5 fitting to connect a tube, and discharge air in a place where water and oil will not enter the interior.
Note) Component parts Aoolicable manifold base MBF261--3;-18 M a n i i o l d b l o c k O , C l a m p O ' O o r i n g O ' O ' O ' O Adapter O , Pin housing. Guide. Insertllug lead wire Plug-in type Connector lead wires o Manilold block assy ' :o-side ports A, B l-1l8 P A, B bottom 2-1l8 P, A, B bottom w/ (114 A, B side) MBF261.-3r-1A M a n i f o l d b l o c k O , C l a m p O , @ .
B side Tubing Extension Union Elbow LQ1E-T A side Metric size A side B side Part no.
A A A A A A A Model A B C D E Fn G H J K XLC-25 50 120 48 1 12 40 26 39 27.5 8 XLC-40 65 171 66 2 11 55 41 63 36 9 8 XL-OMO0001-A 5 Guaranteed period and range The warranty period is 2 million cycles (under SMC endurance test conditions), 18 months after delivery or 12 months in service, whichever comes first.
"Jumping" is a condition in which the cylinder operates without control at a speed that is higher than the control speed.
Supply the power from a stable source, free from surges. from a stable source, free from surges. 3.
A Work load [kg] Work load [kg] LEJ LEJ 40 Lead 20: LEJS63A Lead 16: LEJS40A Lead 30: LEJS63H 30 Lead 24: LEJS40H LEL A 20 A LEM 10 A A 0 LEY 0 200 400 600 800 1000 1200 1400 1600 1800 0 200 400 600 800 1000 1200 1400 1600 1800 Speed [mm/s] Speed [mm/s] LES Vertical Vertical LEPY LEPS 10 20 Lead 10: LEJS63B Lead 8: LEJS40B A Area where the regeneration option is required.
When a cylinder is used in a clamping mechanism, there is a danger of work pieces dropping if there is a decrease in clamping force due to a drop in circuit pressure caused by a power outage, etc. Therefore, safety equipment should be installed to prevent damage to machinery and human injury.
A vacuum pad is a consumable part, so it is warranted for a year after it is delivered. A vacuum pad is a consumable part, so it is warranted for a year after it is delivered. A vacuum pad is a consumable part, so it is warranted for a year after it is delivered.
When the cylinder is used with a clamping mechanism, there is a danger of work pieces dropping out of it if there is a decrease in clamping force due to a drop in circuit pressure caused by a power outage. Therefore, safety equipment should be installed to prevent damage to machinery and human injury.
Caution indicates a hazard with a low level of risk which, if not avoided, could result in minor or moderate injury. Caution: Warning indicates a hazard with a medium level of risk which, if not avoided, could result in death or serious injury. Warning: Danger : Danger indicates a hazard with a high level of risk which, if not avoided, will result in death or serious injury.
Actuator drive Provide ventilation when using a valve in a confined area, such as in a closed control panel.
Devise a safe system so that if a person engages the emergency stop or if a safety device is tripped during a system malfunction,such as a power outage, the operation of the magnet gripper will not cause a hazard to humans or damage the equipment. 7. Consider the action when operation is restarted after an emergency or abnormal stop.
Consider the possibility of a reduction in the circuit air pressure caused by a power failure. Operate the product within a range such that the ! Caution There is a danger of workpieces dropping if there is a decrease of thrust due to a drop in circuit pressure caused by piston will not collide and be damaged at the stroke end. a power outage, etc.
Devise a safe system so that if a person engages the emergency stop or if a safety device is tripped during a system malfunction,such as a power outage, the operation of the magnet gripper will not cause a hazard to humans or damage the equipment. 7. Consider the action when operation is restarted after an emergency or abnormal stop.