EX250-SEN_eng Two power supplies Power cable Brown: 24 VDC (for solenoid valves/output) NOTE If the stored address of an EX250 is not known, please go to the "DHCP Mode" section. White : 0 V (for solenoid valves/output) 2 1 The following instructions must be followed during maintenance: Turn off the power supply.
Since the lock may be released due to reverse exhaust pressure flow, use an individual exhaust type manifold or single type valve. 4. Branch off the compressed air piping for the lock unit between the cylinder and the speed controller. Use of an external branch may cause a reduction in service life. 5.
Normally open Material Solenoid coil Body Seal Brass/BC6, Stainless steel NBR, EPDM, FKM Coil: Class B, Class H Model Rated voltage AC Standard Option 100 V, 200 V 48 V, 110 V, 220 V, 240 V Orifice size (mm) Model Port size Rc 1/4, 3/8 10 VXZ223 2 0 Rc 1/2 15 VXZ224 2 DC 24 V 12 V 0 Standard Option Rc 3/4 20 VXZ235 2 0 Rc 1 25 VXZ236 2 0 5 Series VXZ22/23 Pilot Operated 2 Port Solenoid
26 23 20 26 30 29 10 30 29 10 ISA2 77 77 99 99 IS 126 126 R 3/8 R 3/8 ZSM PF2 IF Dripproof type ISG210 to 291-030 (Without hysteresis scale plate) ISG210 to 231-031 (With hysteresis scale plate) Data Hysteresis adjusting bolt Hysteresis adjusting bolt Setting pressure adjusting bolt Setting pressure adjusting bolt 75 18 8.5 110 56 175 110 56 175 93 8.5 30 2.3 2.3 30 3-6.3 3-6.3 23 20 26
Absolutely never use in an atmosphere where explosive gases are used. The compact manometer does not have explosion proof construction. If used in an atmosphere of explosive gases, there is a possibility of causing an explosion, and therefore, should absolutely not be used under these conditions. 1. The compact manometer can be used for measurement of air and non-corrosive gases.
Absolutely never use in an atmosphere where explosive gases are used. The compact manometer does not have explosion proof construction. If used in an atmosphere of explosive gases, there is a possibility of causing an explosion, and therefore, should absolutely not be used under these conditions. 1. The compact manometer can be used for measurement of air and non-corrosive gases.
6 q w e r t y u i Block packing !
IDX-OM-W020-C / Series IDFB3E-11 -A,S IDFB4E-11 -A,R,T,S,V IDFB6E-11 -A,K,R,T,S,V IDFB8E-11 -A,K,R,T,S,V IDFB11E-11 -A,K,R,T,S,V IDFB15E-11 -K,R,T,S,V URLhttps://www.smcworld.com/ English instruction manual can be downloaded from our URLhttps://www.smcworld.com/ SMC () * 1 ) JIS B8370 * 2 ) ISO4414 *1) ISO 4414: Pneumatic fluid power General rules and safety requirements for systems
R E E B A H 2-P Port size 2-P A 2-M Thread depth N B H Port size 2-M Thread depth N L L K K Conduit terminal: T F (Q) 34 25 U R C G1/2 E B A H D 2-P Port size (S) 2-M Thread depth N L K (mm) Electrical entry P Port size Model Grommet: G Conduit: C Conduit terminal: T M L K H F E D C B N A U S R Q R Q R Q M4 12.8 14 28 12.5 6.5 31 64 28 4.5 13.5 83 66 50 99 50 44 59 22 1/8 VCB21 M4 12.8 18
TSUBAKI CABLEVEYOR cross-sectional dimensions (mm) A Series A B H S LJ1 10 LJ1 20 LJ1 30 10 20 B H S H S 10 20 14 40 H S Example) For LJ1 10 2 3 6 4 8 8 4 Correct: 60% or less Incorrect: More than 60% 103 Made to Order/Clean Room Specification Series LJ1H10 Dimensions/LJ1H10 (X60) 1 2 Scale: 20% Dimensions inside ( ) are for the model with brake. 120 40 70 2-5H10 depth 8 4-Limit switch mounting
(mm) Thread R(PT) Part No. H (Hex.)
If resetting fails, an investigation by SMC Corporation will be required. Displayed in the case of an internal data error.
Dimensions IN574-95 (Sensor head + Display part) 20 40 230 D-F8N (2 pcs.) 110 Red tape 500 20 M12 Connector Tube (3 places) Green tape Sensor head Wiring Terminal no. Description Note 1 +15 V 1 2 1 2 5 2 Output signal 1 D-F8N 3 4 3 4 Display part 3 GND Socket connector A-coded (Normal key) Plug connector A-coded (Normal key) 4 Output signal 2 D-F8N DD1677
Install an air filter. Install an air filter upstream near the valve. Select an air filter with a filtration size of 5 m or smaller. 3. Take measures to ensure air quality, such as by installing an aftercooler, air dryer, or water separator. Compressed air that contains a large amount of drainage can cause the malfunction of pneumatic equipment, such as valves.
Power supply cable (LEC-CK1-1) is an accessory.
Insulation type Electrical entry Electrical option Class B G C D, T S Note) S L, Z 1 (100 V) 2 (200 V) 3 (110 V) 4 (220 V) 7 (240 V) 8 (48 V) 5 (24 V) 6 (12 V) AC DC Note) Surge voltage suppressor is attached in the middle of a lead wire. 17-3-72 3 The VX series will be revised shortly.
(Example) 2000mm lead wire length Cover Groove Pin 300mm 600mm 1000mm 1500mm 2000mm 2500mm 3000mm 5000mm Lever 6 10 15 20 25 30 50 DC indicator Socket DXT170-71-1 For DC SY114-5LOZ SY100-30-4A-20 For AC SY114-1LOZ SY100-30-1A-20 Connector Hook Lead wire 10 World Wide Support... Europe ENGLAND SMC Pneumatics (U.K.) Ltd.
Not required (Use turbine oil Class 1 ISO VG32, if lubricated.) 5 to 50C (Air operated type: 60C) PA AC (50/60 Hz) DC VNC1 VNC Applicable pressure range 100 V, 200 V, Other voltage (Option) Coil rated voltage (V) 2 4 PAX 24 V, Other voltage (Option) 15% to +10% of rated voltage Class B or equivalent (130C) 1 4 VNC Allowable voltage fluctuation Coil insulation type Pressure VNC2 PB External