Air Pilot Operated Series NVSA L..k.g.: Port to porl (internal) not 1o exceed 0.m7 cubic feet per minule at 100 PSIG (6.9 Kgtcm'). Op.r.Sng Pr..rur..! 28 'Vacuuh to 30o FSIG (20 Kglrcm?).
At least one valve coil has a short circuit, or at least one connected module has a short circuit, or the module layout has changed. Self-test has failed and a power reset is required. An incompatible module is connected to the SI unit.
10 mA (2 V or less at 40 mA) 4V or less 0.8 V or less at 10 mA (2 V or less at 40 mA) Current leakage 0.8mA or less 100A or less at 24 VDC 0.8mA or less 100A or less at 24 VDC Indicator LED Red LED illuminates when turned ON.
(Values at the initial period) Vibration resistance: No malfunction occurred in a one-sweep test between 45 and 2000 Hz. Test was performed at both energized and deenergized states in the axial direction and at the right angles to the main valve and armature.
Too large resistance of In particular, attention should be paid to the piping equipment used and fittings because they are often missed. on the way of Equipment and piping at the exhaust side should piping also be of an appropriate size. Operation at a very low speed can create a The product 1.
20 30 40 Symbol Nil B* H* Symbol 02 03 04 *Note: Bracket and/or panel mount nut are not assembled and are supplied loose at time of shipment.
20 30 40 Symbol Nil B* H* Symbol 02 03 04 *Note: Bracket and/or panel mount nut are not assembled and are supplied loose at time of shipment.
Test was performed at both energized and deenergized states in the axial direction and at the right angles to the main valve and armature.
one end) 1 place Current (Wired) SI unit: 15 units 1 line (Connector at one end) 14 lines (Connector at both ends) 29 places Interchangeability maintained * Maximum I/O of wireless master/ slave unit is limited to 128 points.
Corxtruction./ Parts List 27A' PartsList Note: The rotation specilication of270', the point of minimum rotation 20' is a limit shifring point even il the switch is shifted to make rotation of switch as shown in the left diagram. (E\ren if switch is shitted tothe maximum, switchon will be made at the point prior to the stopping ooint at 20'.)
Note 3) When using seal material PTFE at 15 cm3/min (under water pressure) or less. Note 4) Vibration resistance Conditions when tested with one sweep of 10 to 250 Hz in the axial direction and at a right angle to the armature, in both energized and deenergized states. No malfunction occurred when tested (value at the initial state).
Turn it in the counter-clockwise direction at 90o, and it is locked. Turn it right to release. 3.8 Change of electrical entry Wire entry can be changed by mounting the housing in either direction (four directions at every 90) after dividing the terminal block and the housing. For the indicator lighted style, be careful not to damage the light with the lead wire of the cable.
Corxtruction./ Parts List 27A' PartsList Note: The rotation specilication of270', the point of minimum rotation 20' is a limit shifring point even il the switch is shifted to make rotation of switch as shown in the left diagram. (E\ren if switch is shitted tothe maximum, switchon will be made at the point prior to the stopping ooint at 20'.)
Test was performed at both energized and de-energized states in the axial direction and at the right angles to the main valve and armature.
mA DC, 0 to 20 mA DC (Sink type) Voltage type 0 to 5 VDC, 0 to 10 VDC Input signal Preset input type 4 points (Negative common) Current type 500 or less Voltage type 6.0 to 6.5 k (at 25C) Input impedance Preset input type Approx. 4.7 k 1 to 5 VDC Output impedance: 1 k or more Output accuracy: 6% F.S. or less Analog output Symbol 4 to 20 mA (Sink type) Output impedance: 250 or less Output
Auto drain Check the auto drain is working properly at least once a day.
to cylinder, Needle fully open (2) Load ratio {(Load weight x 9.8) Theoretical output} x 100% Speed at the end (u) Time (s) SOL: ON(OFF) 1-2-4 1-2-5 4 Series SV Air Cylinders Drive System Full Stroke Time and Speed at the End Air Cylinders Drive System Full Stroke Time and Speed at the End Series SV3000 Applicable bore size: 50, 63, 80, 100 Series SV4000 Applicable bore size: 63, 80, 100
AS121FG-M5 AS231FG-01 R(PT) 1/8 20, 25, 32 AS221FG-01 AS231FG-02 R(PT) 1/4 20, 25, 32, 40 AS221FG-02 AS331FG-02 R(PT) 1/4 40, 50, 63 AS321FG-02 AS331FG-03 R(PT) 3/8 40, 50, 63 AS321FG-03 AS431FG-04 R(PT) 1/2 63, 80, 100 AS421FG-04 AS131FG-U10/32 10-32UNF 6, 10, 16, 20 AS121FG-U10/32 AS231FG-N01 NPT1/8 20, 25, 32 AS221FG-N01 Elbow type AS231FG-N02 NPT1/4 20, 25, 32, 40 AS221FG-N02 AS331FG-N02
0 Insert pin assembly replacement screw Cut the end of the tubing y at a right angle and pass it through the fitting nut u.
] 10 2250 lbf [10 KN] Relief port Nil No V Yes Stroke Sensor type Symbol Stroke (Applicable model) 12 12 mm (MACM2) 20 20 mm (MACM4) 30 30 mm (MACM6) 50 50 mm (MACM10) Nil Unsupported P Port side photo sensor mounted type B Port back side photo sensor mounted type Specications Precautions Model MACM2-12 MACM4-20 MACM6-30 MACM10-50 Max. allowable load weight lbf [KN] 450 [2] 900 [4] 1350 [