IN20267 Install the EDS file by selecting Tools then EDS Hardware Installation Tool. Figure 13-1 EDS Tool Continue importing the EDS file by following the prompts then select the EDS file obtained from the www.smcusa.com website. 23 - IN20267 Adding a device to Ethernet Rockwell Studio 5000 13.2. Add the Ethernet MPC by right clicking on Ethernet then clicking on New Module 13.2.1.
Spacer with bracket Retainer Nut Tentative tightening by fingers is possible. 1 Modular F.R.L.
Unit No. is the No. to identify each Thermo-cons when 2 or more Thermo-cons are linked by communication. Set this No. within 0-F. (UT is the code adding 30H to unit No. from 30H to 3FH.) As for symbols at communication, minus is indicated by (2DH by ASCII code) and plus is indicated by 0 (30H by ASCII code).
Configuration Minimum equipment and wiring requirements to get started Provided 1 Ex) 200 V AC (*1) by customer 5 6 Provided 1 by customer 7 2 3 (-) PC 1 2 (+) 8 4 C D 11 21 9 11 U 2 Electric Actuators Ex) LEF V W 3 Provided by customer 10 (Positioning unit/Motion controller) (*1)Refer to LECSS Operation Manual, Chapter 3 if the power supply voltage is 100VAC. 1 Driver LECSS*-S* 2 Motor cable
Do not carry a cylinder by the auto switch lead wires. Never carry a cylinder by its lead wires. This may not only cause broken lead wires, but it may cause internal elements of the switch to be damaged by the stress. 3. Mount switches using the proper tightening torque. When a switch is tightened beyond the range of fastening torque, the mounting screws or switch may be damaged.
When the counter is reset by pressing the cylinder rod to the reference plane, that point becomes the home position.
Even with the same product number, the table of some products can be moved by hand and the table of some products cannot be moved by hand. However, there is no abnormality with these products.
Page 24 Distributed by Power Aire, Inc. (800) 526-7661
Do not carry a cylinder by the auto switch lead wires. Never carry a cylinder by its lead wires. This may not only cause broken lead wires, but it may cause internal elements of the switch to be damaged by the stress. 3. Mount switches using the proper tightening torque.
The required lifting force can then be determined by dividing the theoretical lifting force by the safety factor t.
Measurement instruments that SMC manufactures or sells have not been qualified by type approval tests relevant to the metrology (measurement) laws of each country.
The air which has had its moisture removed is heated in two stages by the re-heater (heat exchanger) in the cooler re-heater and by the second re-heater, and is supplied to the outlet side as warm and dry air.
The proper operating range can be determined by the color of the light.
: Made by HIROSE ELECTRIC CO., LTD.)
The average speed of the cylinder is obtained by dividing the stroke by the total stroke time.
Do not carry a cylinder by the auto switch lead wires. Never carry a cylinder by its lead wires. This may not only cause broken lead wires, but it may cause internal elements of the switch to be damaged by the stress. 3. Mount switches using the proper tightening torque. When a switch is tightened beyond the range of fastening torque, the mounting screws or switch may be damaged.
Rapid neutralization of static electricity by a feedback sensor The discharge speed has been increased by reading the workpieces electrostatic potential by the feedback sensor and continuously emitting ions with a reverse polarity.
Any damage attributed to use beyond the specifications is not covered by the warranty. 2. There is a possibility of dangerous sudden action by the product if the sliding parts of the machinery are twisted due to external forces, etc. In such cases, human injury may occur, such as by hands or feet getting caught in the machinery, or damage to the machinery itself may occur.
Lock unit Cylinder Holding force improved by 15% (MNB, 50: 1370 N a MWB: 1570 N) High stopping accuracy within 1 mm (With 50 and 30 kg of load) Overall length reduced by 18 mm max.