Function: 2 (2 Position Double), Piping: 3 (Body Ported), Exhaust: 3 (Common), Low Wattage: None, Pressure Specification: K (High-pressure, 1MPa), Coil Specification: Standard, Voltage: 5 (24VDC), Lead Wire: DO (DIN Connector w/o Connector), Light/Surge Suppressor: Without light/surge voltage suppressor, Manual Override: Non-locking Push Type, A, B Port Size: 01 (1/8)
Do not service or attempt to remove product and machinery/equipment until safety is confirmed. 1.The inspection and maintenance of machinery/equipment should only be performed after measures to prevent falling or runaway of the driven objects have been confirmed. 2.When the product is to be removed, confirm that the safety measures as mentioned above are implemented and the power from any
expressed in hexadecimal. (10 to 15 in decimal number are expressed as A to F) Forced-lock release terminal Note 4) I/O cable: 5 or less, Actuator cable: 20 or less Natural air cooling 0 to 40 (No freezing) 90 or less (No condensation) 10 to 60 (No freezing) 90 or less (No condensation) Between the housing and SG terminal: 50 (500 VDC) 130 (Screw mounting), 150 (DIN rail mounting) Note 1) Do
10 20 Cooling system Natural air cooling Operating temperature range [C] Note 6) Screw mounting: 0 to 40 (No freezing) Screw mounting: 0 to 30 (No freezing) Operating humidity range [%RH] Note 7) 90 or less (No condensation) Insulation resistance [M] Between the housing and SG terminal: 50 (500 VDC) Weight (including batteries) [g] 410g (Screw mounting) 430g (DIN rail mounting) Note 1) Do
The material and fluid compatibility check list provides reference values as a guide only, therefore we do not guarantee the application to our product. The data above is based on the information presented by the material manufacturers. SMC is not responsible for its accuracy and any damage happened because of this data. 4
Thoroughly flush out the connector piping and be sure that dirt and chips, etc., do not get inside the equipment. 2. When wiring, except for the D-sub connector entry, solder to the probe socket of the AHC unit, or the terminal of the tool adapter. We recommend insulating the connection points with heat shrinking tube, etc. 3.
Do not disassemble the trunnion style. Seal kit includes a grease pack (40, 50: 10 g, 63, 80: 20 g, 100: 30 g). Order with the following part number when only the grease pack is needed. Grease pack part no.: GR-S-010 (10 g), GR-S-020 (20 g) 39
Do not replace the bushings. The bushings are press-fit. To replace them, they must be replaced together with the cover assembly. 2. To replace a seal, apply grease to the new seal before installing it. If the cylinder is put into operation without applying grease to the seal, it could cause the seal to wear significantly, leading to premature air leakage. 3.
Do not replace the non-rotating guide. Since the non-rotating guide is press fitted, the entire cover assembly needs be replaced instead of a single part. 200
Do not replace the non-rotating guide. Since the non-rotating guide is press fitted, the entire cover assembly needs be replaced instead of a single part. 202
Do not disassemble the trunnion style. Seal kit includes a grease pack (40, 50: 10 g, 63, 80: 20 g, 100: 30 g). Order with the following part number when only the grease pack is needed. Grease pack part no.: GR-S-010 (10 g), GR-S-020 (20 g) 35
CA2H100A-PS Do not disassemble the trunnion style. Seal kit includes !4, !5 and !6. Order the seal kit based on each bore size. Seal kit includes a grease pack (40, 50: 10 g, 63: 20 g). Order with the following part number when only the grease pack is needed. Grease pack part no.: GR-S-010 (10 g), GR-S-020 (20 g) 40
Piston seal NBR Cushion valve seal NBR O-ring MBW100-PS Cylinder tube gasket NBR Do not disassemble the trunnion style. Seal kit includes !2, !3, !4 and !6. Order the seal kit based on each bore size. Seal kit includes a grease pack (40, 50: 10 g, 63, 80: 20 g, 100: 30 g). Order with the following part number when only the grease pack is needed.
CA2WH100A-PS Do not disassemble the trunnion style. Seal kit includes !0, !1 and !2. Order the seal kit based on each bore size. Seal kit includes a grease pack (40, 50: 10 g, 63 or more: 20 g). Order with the following part number when only the grease pack is needed. Grease pack part no.: GR-S-010 (10 g), GR-S-020 (20 g) 41
Do not replace the bushings. The bushings are press-fit. To replace them, they must be replaced together with the cover assembly. 2. To replace a seal, apply grease to the new seal before installing it. If the cylinder is put into operation without applying grease to the seal, it could cause the seal to wear significantly, leading to premature air leakage. 3.
Do not replace the bushings. The bushings are press-fit. To replace them, they must be replaced together with the cover assembly. 2. To replace a seal, apply grease to the new seal before installing it. If the cylinder is put into operation without applying grease to the seal, it could cause the seal to wear significantly, leading to premature air leakage. 3.
Note 4) When using the D-M9lA(V) or Y7BA, do not use the steel set screws which are included with the above auto switch mounting brackets (BA7-lll, BA4lll). Order a stainless steel screw kit (BBA1) separately, and use the M4 x 6 L stainless steel set screws included in the BBA1. Note 5) There is a difference in the cylinder tube thickness depending on the cylinder model.
When washing the element, do not wipe it using a stiff brush or rag.
Do not use a stop valve to prevent damage to the differential pressure gauge if the valve is inadvertently left open or closed. 2) Install the differential pressure gauge vertically. 3) The piping of the differential pressure gauge must be connected securely because it will break if it becomes detached.
Additionally, do not put the tube end in the liquid. This may cause the back pressure to be applied, resulting in poor performance. 3.Liquids cannot be collected by the air. 1076 A