Slider Type Ball Screw Drive/11-LEFS Series . * If the step motor and servo motors do not meet your specifications, also consider the AC servo specification (Page 46). 38 Model Selection LEF Series Step Motor (Servo/24 VDC) Servo Motor (24 VDC) Clean Room Specication For the LECPA, refer to page 40.
When this is done, take care that the coverings of the lead wires do not enter the core wire crimping area. Use special tool when crimping. (For the crimping tool, please consult with SMC.)
When the line is stopped,do not adjust or set the differenital pressure, as it could cause the differential adjustment valve to break. 3. When setting the pressure differential, if there is a fluctuation in the operating flow rate, set the pressure differential at the lower flow rate range. ITV IC Inlet Outlet VBA VE VY1 G Piping PPA Warning Mist generation part AL 1.
.: B21-1P 0.12 How to Order AP100 01 Cylinder cushion Application Example Special specifications Pressure control valve Thread type Symbol Nil Specifications Symbol Nil N F Type Rc NPT G Set pressure range 0.02 to 0.2 MPa X201 AP100 Accessory Connection thread Symbol Nil B Description With bracket Symbol 01 02 Size 1/8 1/4 Precautions Relief Characteristics Do not use this product as a
Do not use a tool when rotating the handle. When the handle is rotated with a tool, it may apply excessive torque to the handle or inside the valve body and it may cause damage. Rotate the handle by hand. 9. When locking the valve with LOTO feature in the closed position, use safety lockout hasp.
Do not use a tool when rotating the handle. When the handle is rotated with a tool, it may apply excessive torque to the handle or inside the valve body and it may cause damage. Rotate the handle by hand. 9. When locking the valve with LOTO feature in the closed position, use safety lockout hasp.
(To set the pressure, do so in the direction of pressure increase.) 2. Set the outlet pressure to 85% or less of the inlet pressure. Precautions Be sure to read this before handling the products. Refer to back page 50 for Safety Instructions and pages 387 to 391 for Precautions on every series. Inlet pressure (MPa) Mounting/Adjustment Warning 1.
(To set the pressure, do so in the direction of pressure increase.) Pressure gauge and One-touch fittings 1. Both the pressure gauge and the One-touch fittings are a cassette type, so that it is possible to rotate them freely. Rotate them after confirming that there is no pressure inside and exhausting air completely. 714
Screw the locking ring into the switch (do not tighten with pliers, hand tishten only). Lead Wire with Connector Length 0.5 m 3 m 5 m Part no.
Note) Do not apply rotational torque to the piston rod. When the stroke reading cylinder is used near a motor, welding machine or other source of noise generation, there is a possibility of miscounting. In this case, noise should be suppressed as much as possible and the following countermeasure should be taken. 1. Connect the shield wire to FG (flame ground). 2.
Do not use it in such a way that a load could be applied to the piston rod during the retraction. The spring that is built into the cylinder provides only enough force to retract the piston rod. Thus, if a load is applied, the piston rod will not be able to retract to the end of the stroke.
Do not add the suffix (N) indicating no lead wire to the part numbers of models D-A3A, A44A. G39A and K39A. Lead wire length symbols: 0.5 m Nil (Example) C73C 3 m L (Example) C73CL 5 m Z (Example) C73CZ None N (Example) C73CN In addition to the models in the above table, there are some other auto switches that are applicable.
Load Load (a) (b) Thrust bearing Flexible coupling Bearing Size Allowable thrust load (N) Allowable radial load (N) (a) (b) 10 15 20 30 40 7.8 15.7 14.7 9.8 19.6 19.6 29.4 49 49 49 98 78 59 108 98 MSQX Do not allow the load and moment applied to the table to exceed the allowable values shown in the table below.
1. 7 stations (15 stations) Note 1) Be careful that the packing and the O-ring do not fall out of the groove. Note 2) The tightening torque of bolt !1 should be 2 to 2.2 N. (2) (1) 8 stations Note 1) Regardless of the D-sub connector mounting position, stations are to be counted from D side as the 1st one. Note 2)D-sub connector can use up to 8 stations in on side fitting (Type FD U).
1. 7 stations (15 stations) (2) (1) Stations Note 1) Be careful that the packing and the O-ring do not fall out of the groove. Note 2) The tightening torque of bolt !1 should be 2 to 2.2 N. Note 1) Regardless of the D-sub connector mounting position, stations are to be counted from D side as the 1st one. Note 2) D-sub connector can use up to 8 stations in on side fitting (Type FD U ).
DOZ is not available. 2 Other Option Electrical entry 3 position closed center G: Grommet Lead wire length 300 mm L: L plug connector With lead wire LN: L plug connector Without lead wire LO: L plug connector Without connector D: DIN terminal 3 3 position exhaust center 4 M: M plug connector With lead wire MN: M plug connector Without lead wire MO: M plug connector Without connector DO:
Model Pressure range *1 Indication unit Connection thread Note MPa Port size 01 Rc1/8 02 Rc1/4 R1/8 R1/4 G46-7-02-SRB 0 to 0.7 R1/4 G46-10-02-SRB 0 to 1.0 G46-4-01 to 02-SRB 0 to 0.4 MPa Set pressure range: 0.05 to 0.69 MPa 02 WR110 X215 *1: Do not apply more pressure than the max. pressure displayed. It may cause a malfunction.
(Do not use any tools.) The initial exhaust rate is adjusted by turning the adjustment nut counterclockwise.
To prevent this, do not set the supply pressure higher than necessary. Soft workpiece Workpiece that has concave/convex surfaces As soft workpieces are easy to deform, there is a tendency for the workpiece to touch the bottom of the non-contact gripper. Please be aware that the workpiece may touch the gripper before using.
Do not tighten the initial air supply flow any further than the minimum supply flow position, as this may result in component damage, or in increased time needed to attain a vacuum in the vacuum chamber due to a decline in the displacement capabilities of the gas accumulation part (bellows chamber). 1.