Vacuum Pad Do not service or attempt to remove product and machinery/ equipment until safety is confirmed. 1. The inspection and maintenance of machinery/equipment should only be performed after measures to prevent falling or runaway of the driven objects have been confirmed. 2.
Do not apply an impact or large force to a pad when adsorbing a workpiece. This will cause deformation, cracking and wear of the pad to be accelerated. The stiffening ribs, etc. should touch lightly, while staying within the pad skirts deformation range. Positioning should be performed accurately. Especially in the case of small diameter pads. 6.
When this is done, take care that the coverings of the lead wires do not enter the core wire crimping area. (Crimping tool: model no. DXT170-75-1) Set point ON When assembling the connector to the switch housing, push the connector straight onto the pins until the lever locks into the housing slot.
Do not use a pair of pliers, nippers, or scissors because they could result in an uneven cut or cause the tube to become flattened. As a result, it might not be possible to connect the tubing, or after the tube has been connected, it could pull out or allow air to leak.
Do not replace the bushings. The bushings are press-fit. To replace them, they must be replaced together with the cover assembly. 2. To replace a seal, apply grease to the new seal before installing it. If the cylinder is put into operation without applying grease to the seal, it could cause the seal to wear significantly, leading to premature air leakage. 3.
Do not replace the bushings. The bushings are press-fit. To replace them, they must be replaced together with the cover assembly. 2. To replace a seal, apply grease to the new seal before installing it. If the cylinder is put into operation without applying grease to the seal, it could cause the seal to wear significantly, leading to premature air leakage. 3.
Do not replace the bushings. The bushings are press-fit. To replace them, they must be replaced together with the cover assembly. 2. To replace a seal, apply grease to the new seal before installing it. If the cylinder is put into operation without applying grease to the seal, it could cause the seal to wear significantly, leading to premature air leakage. 3.
Do not replace the bushings. The bushings are press-fit. To replace them, they must be replaced together with the cover assembly. 2. To replace a seal, apply grease to the new seal before installing it. If the cylinder is put into operation without applying grease to the seal, it could cause the seal to wear significantly, leading to premature air leakage. 3.
/set) do not include a grease pack (10 g), order it separately. Grease pack part no.: GR-S-005 (5 g) 7
Do not use a stop valve to prevent damage to the differential pressure gauge if the valve is inadvertently left open or closed. 2) Install the differential pressure gauge vertically. 3) The piping of the differential pressure gauge must be connected securely because it will break if it becomes detached. 1.
Do not allow the weight of piping to lie directly on air dryer. Operating Environment Caution The air that has been used for reactivating the adsorption agent and the air that has passed through the indicator are discharged externally from the heatless air dryer. Therefore, use the dryer in an area where the discharge will not be a problem.
Note) Do not apply rotational torque to the piston rod. When the stroke reading cylinder is used near a motor, welding machine or other source of noise generation, there is a possibility of miscounting. In this case, noise should be suppressed as much as possible and the following countermeasure should be taken. 1. Connect the shield wire to FG (flame ground). 2.
Do not add the suffix (N) indicating no lead wire to the part numbers of models D-A3A, A44A. G39A and K39A. Lead wire length symbols: 0.5 m Nil (Example) C73C 3 m L (Example) C73CL 5 m Z (Example) C73CZ None N (Example) C73CN In addition to the models in the above table, there are some other auto switches that are applicable.
Do not indicate suffix N for no lead wire on D-A3/A44/G39/K39 models.
.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com Lead wire length indication D-A9/A9V The above auto switches do not have internal contact protection circuit. 1. Operating load is an inductive load. 2. The length of wiring to the load is 5 m or more. 3. The load voltage is 100 VAC.
Screw the locking ring into the switch (do not tighten with pliers, hand tishten only). Lead Wire with Connector Length 0.5 m 3 m 5 m Part no.
Band Switch operating position (OFF) 7 8 8 9 7 9 The difference between the operating position (ON) of switch and the returning position (OFF) is 2 mm or less in a reed switch and 1 mm or less in a solid state switch. 10.5 10.5 13 Rail 6 5 5 6 5 6 6-11-45 6-11-45 45 Series C85 Contact Protective Box CD-P11, CD-P12 Contact Protective Box/Internal Circuit D-A7/A8 and D-C7/C8 reed switches do
Do not use it in such a way that a load could be applied to the piston rod during the retraction. The spring that is built into the cylinder provides only enough force to retract the piston rod. Thus, if a load is applied, the piston rod will not be able to retract to the end of the stroke.
Releasing the lock Do not release the lock while a load is applied to the lock. This will cause a sudden, erratic movement of the cylinder, and create a dangerous condition. Control circuit 1. To control the end lock cylinder, use a 2 position 4/5 port solenoid valve. Avoid using these valves along with a 3 position solenoid valve (especially a closed-center metal seal type). 2.
or fingers from getting caught in the gap between the cylinder body and the plate when air is applied. 50 MGQM50 2.54 3.09 3.65 4.21 4.77 5.33 5.89 6.45 63 MGQM63 3.01 3.63 4.23 4.85 5.47 6.09 6.71 7.33 80 MGQM80 5.66 6.59 7.49 8.41 9.33 10.25 11.17 12.09 100 MGQM100 8.96 10.27 11.57 12.90 14.23 15.56 16.89 18.22 Caution Weight/Ball Bushing Bearing: MGQL12 to 100 (kg) 1.Do