High Vacuum Angle Valve, XL Series Impingement frequency 15 The impingement frequency of gas molecules on a unit surface area is Z=3.53 x 1022P/(MT)1/2 collisions/sec cm where M is the quantity of molecules, T is the absolute temperature (K), and P is the pressure. In the case of oxygen at room temperature and 10-6Torr, one atomic layer impinges in a few seconds. O After a few seconds at 10-6Torr 41
Extend the dimensions of A and H, when using a single/double knuckle joint together with a rod end nut.
Relay, PLC Grommet Yes 2-wire 12 V Lead wire length symbols: 0.5 m Nil (Example) M9BV 3 m L (Example) M9NL 5 m Z (Example) M9NZ Auto switches marked with a symbol are produced upon receipt of order.
Relay, PLC Grommet Yes 2-wire 12 V Lead wire length symbols: 0.5 m Nil (Example) M9BV 3 m L (Example) M9NL 5 m Z (Example) M9NZ Auto switches marked with a symbol are produced upon receipt of order.
How to replace the pad of the basic (ball joint) type ZP series Compact Type ZP3 Series Model Connection thread Tightening torque [Nm] ZP3-T(015 to 035)U-A3 M3 x 0.5 0.2 to 0.25 ZP3-T(04 to 16)-A5 M5 x 0.8 1.3 to 1.7 Pad diameter: 10 to 32 z Insert a hexagon wrench into the bottom of the pad, loosen the screw, and remove the old pad from the adapter. x Place a new pad on the adapter, and,
2 is not energised, the valve element A t connected to the piston u is closed by the return spring i. Then valve element B y connected to the valve element A t is open. When the pilot operated solenoid valve !2 is energized, the pilot air supplied to the bottom of the piston u moves upward to open the valve element A t and closes the valve element B y. Because rod !
R 04 Z A q w e r u t y N Common Supply Type 1.
B A B 2 position single 2 position double R1 R2 P R1 R2 P e y t r w w q q t r A B A B SY i SYJ R1 P R2 R1 P R2 i SX u 3 position closed center/exhaust center/pressure center VK 3 position closed center VZ A B w t q r R1 R2 P VF 3 position exhaust center A B A B VFR R1 R2 P VP7 3 position pressure center i A B VP4 R1 P R2 (This construction shows a closed center) R1 R2 P Component Parts Replacement
Type/ZP3-T ZP3-T-B ZP3-T-A w w e q q ZP3-T-A-B ZP3-T-A-(02/04) w t r q Component Parts No.
When using a single/double knuckle joint together with a rod end nut, the A and H dimensions should be extended.
M12 connector pin number X X VP544(R)/744(R)-X538 Internal pilot External pilot External pilot/With check valve 2(A) 2(A) 2(A) y t r y t r y t r w q e w q e w q e 3(R) 3(R) 3(R) y t r y t r y t r w q e w q e w q e 3(R) 3(R) 3(R) 1(P) 1(P) 1(P) X X VP544(R)/744(R)-X555 Internal pilot External pilot External pilot/With check valve 2(A) 2(A) 2(A) y t r y t r y t r 3(R) w q e 3(R) w q e w q e
Z AFD20 to 40 When more than one specification is required, indicate in ascending alphanumerical order. Note 5) Without a valve function.
th the regulalor a a a a a a a a a a a a a a a a a a o a a a r t a a a a a a a o a a AW With digital pressure switch with display fitf"r r.gut"t;f outDut specificalions (tsE30-01-!!
Calculate the load factor for each direction. x = Xc/Lx, y = Yc/Ly, z = Zc/Lz 5. Confirm the total of x, y, and z is 1 or less. x + y + z 1 When 1 is exceeded, please consider a reduction of acceleration and work load, or a change of the work load center position and series. Acceleration [mm/s2]: a Work load [kg]: m Work load center position [mm]: Xc/Yc/Zc z y 1. Horizontal 3.
t t t B1 H1 (mm) (mm) (mm) Dd9 Applicable bore size (mm) L L Dd9 d l l d m t Snap ring Snap ring t m Part No.
(When port sizes for A, B ports are mixed, indicate C4 or C6 in cell .)
Check using a feeler gauge that the clearance between the position indicator (109) and the electronics cover is 1 mm. 7 ND90 71 en 17 N O I T A C O L S U O D R A Z A H N O I T A C O L S U O D R A Z A H N O N ND9000H Valve Positioner Position Transmitter X300 Ui (Vmax) = 28 V Ii (Imax) = 120 mA Pi (Pmax) = 1 W Li = 53 uH Ci = 22 nF Ex i Barrier + 1 Uo (Voc) 28 V Io (Isc) 120 mA Po 1 W
(mm) Internal cross section a (mm 2) Nominal size = Length of piping [mm] a = Internal cross section of piping [mm 2] T 0425 T 0604 TU 0805 T 0806 1/8B T 1075 TU 1208 T 1209 1/4B TS 1612 3/8B T 1613 1/2B 3/4B 1B 4 2.5 4.9 [l (ANR)] QC = Air consumption required for one reciprocation of rotary table 6 4 12.6 8 5 19.6 8 6 28.3 6.5 33.2 7.5 10 44.2 12 8 50.3 12 9 63.6 9.2 66.5 16 12 113 12.7