LX Series Compact Electric Actuators For mors infomaiion on these sensors, plase visit ihe SUNX wbsite at www.sunxramco,com ,.t.'
at the stroke end, causing damage to the cylinder.
It will causes malfunctions on control circuit that exhausts at both port such as 3 position valve with exhaust center.
However, when a stroke out of the standard 51 to 599 is required, add "-XB10" at the end of the model no. When stroke exceeds 600 mm, add -XB11 at the end of model no. Refer to page 23 for Made to Order. Applicable auto switches/For detailed auto switch specifications, refer to page 17 through 21. Lead wire length (m) 0.5 (Nil) 3 (L) 5 (Z) Auto switch part no.
Recommended valve/for PB1013 air operated type: SYJ34 Note 2) After initial suction of liquid operating at 1 to 7Hz, it can be used with operation at lower cycles.
Too large resistance of In particular, attention should be paid to the piping equipment used and fittings because they are often missed. on the way of Equipment and piping at the exhaust side should piping also be of an appropriate size. Operation at a very low speed can create a The product 1.
Test was performed at both energized and deenergized states in the axial direction and at the right angles to the main valve and armature.
Total stroke time t Stroke L Stroke mm Speed d% d% Speed at the end Stroke Speed at the end u Time s SOL: ON (OFF) IV Air Cylinder Drive Systems Total Stroke Time and Speed at the End Series SV Series SV3000 Applicable bore size: 50, 63, 80, 100 Applicable related components Total stroke time s Tubing Speed controller Solenoid valve Silencer 0.0 0.2 0.4 0.6 0.8 1.0 1.2 1.4 1.6 1.8 2.0 400
Test was performed at both energized and de-energized states in the axial direction and at the right angles to the main valve and armature.
However, this inrush current will decrease shortly after. * When the product uses multiple heater assemblies, do not turn on the power to each heater assembly at the same time. Turn on the power to each heater assembly one-by-one at intervals of 30 sec. since the inrush current is large. * The heater temperature will decrease several % from the start of heating and then becomes stable.
Fixed end At a temperature of 20C, bend the tubing into a U shape. Fix one end and gradually move the other end closer. Measure 2R at the point where the outside diameters rate of change is 5%. Max.
(at 80 mA load current) PNP: 1.5 V max.
When the cylinder has to be reset at the starting position, install manual safety equipment. Intermediate stop It is difficult for this product to make a piston stop at the required intermediate position accurately and precisely using a 3 position closed center type directional control valve, due to the compressibility of air.
Intermediate strokes For manufacture of strokes other than the standard strokes above, add "-X2" at the end of the part number.
Standard condition: Flow rate converted to a volume at 20C and 101.3 kPa (absolute pressure) Normal condition: Flow rate converted to a volume at 0C and 101.3 kPa (absolute pressure) Response time The response time can be selected to suit the application.
When wiring is done at the factory, positive (+) is red and negative (-) is black. With power saving circuit (JSY3000/5000: Made to Order) Power consumption is decreased to approx. 1/2.5 to 1/4 of the amount consumed at startup by reducing the wattage required to hold the valve in an energized state. (Effective energizing time is over 62 ms at 24 VDC.)
20C, 0.125 MPa at 80C Pressure resistance Resistivity recovery Note 2) 60 min at 10 L/m 100 L/4000 cm2 Pure water cleaning Others Note 1) Filtration accuracy: tested with ultrapure water, flow rate at P = 0.01 MPa.
20C, 0.125 MPa at 80C Pressure resistance Resistivity recovery Note 2) 60 min at 10 L/m 100 L/4000 cm2 Pure water cleaning Others Note 1) Filtration accuracy: tested with ultrapure water, flow rate at P = 0.01 MPa.
It measures the pressure at the time of auto-shift signal input and uses it as the reference pressure to correct the set value on the switch.
Supply pressure drop Supply pressure increase Pressure Supply pressure normal Set value P1 P2 Time