SMC Corporation of America
Elite Part Number Search
Search Results "RZQA32TN-300-50"

If a follow-up operation is performed at a duty ratio of 50% or higher, the upper limit value may change.

Petroleum, Water-glycol, Emulsion: NBR; Phosphoric ester: FKM FH FH HOW Model/Rated Flow Rate Model Port size (Rc) Rated flow rate (L/min) Micromesh Paper FH100-06 FH100-08 FH100-10 FH100-12 FH100-16 FH100-20 FH100-24 3/4 60 50 1 100 80 1 1/4 150 120 1 1/2 200 160 2 300 260 2 1/2 550 450 3 700 600 Description Part no.

Set range is 0 to 300 sec. to Contact input signal 2 OFF detection timer Setting and checking 17. Press the [SEL] key once. The set screen of contact input signal 2 OFF detection timer is displayed on the digital display. PV SV 18. Select contact input signal 2 OFF detection timer from the table below with [] key or [] key, and confirm by pressing SEL.

Set range is 0 to 300 sec. to Contact input signal 2 OFF detection timer Setting and checking 17. Press the [SEL] key once. The set screen of contact input signal 2 OFF detection timer is displayed on the digital display. PV SV 18. Select contact input signal 2 OFF detection timer from the table below with [] key or [] key, and confirm by pressing SEL.

Flow valve High pressure side Series ASQ If the load ratio at the set pressure of the flow valve exceeds 50%, install a dual speed controller (meter-in and meter out control) on the high pressure side.

Bore sizes: 25, 32, 40, 50, 63 mm; Stroke lengths: 200, 250, 300, 350, 400, 450, 500, 600, 700, 800, 900, 1000 mm; Maximum stroke lengths: 4000 mm (25 & 32 bore), 5000 mm (40 bore), 6000 mm (50 & 63 bore); Minimum operating pressure: 0.18 MPa (26 psi); Speed: 50 ~ 300 mm/sec.

/50 Impact/Vibration resistance (m/s2) (1) 1 (P) 3 (R) 5 (R) 1 (P) 3 (R) Note 1) Impact resistance: No malfunction resulted from the impact test using a drop impact tester.

With 50% of signal input 1 0.8 1 0.6 Output deviation factor % F.S.

[MPa] Supply pressure [MPa] Flow rate Characteristics Flow rate characteristics Supply pressure: 0.4MPa Supply pressure: 0.4MPa 100 90 100 90 Vacuum pressure [kPa] Vacuum pressure [kPa] 80 80 70 70 60 60 50 50 40 40 30 30 20 20 10 10 0 0 10 20 30 40 50 60 70 80 90 100 110 120 20 60 100 140 180 220 260 300 130 Suction flow rate [l/min(ANR)] Suction Flow rate [l/min (ANR)] Time to reach vacuum

20 15 4(A) 4(A) 5 46 12.5 P=11 L plug connector (L) Dimensions n: Stations L n 19 226 218 20 237 229 13 160 152 15 182 174 17 204 196 5 72 64 6 83 75 7 94 86 9 116 108 11 138 130 L2 L1 2 39 31 3 50 42 4 61 53 16 193 185 18 215 207 10 127 119 12 149 141 14 171 163 8 105 97 601

400 500 600 700 800 900 1000 0 0 100 200 300 400 500 600 700 800 900 1000 Flow rate l/min(ANR) Flow rate l/min(ANR) ARX21-01 ARX21-02 0.35 0.35 0.30 0.30 Downstream pressure MPa Downstream pressure MPa 0.25 0.25 0.20 0.20 0.15 0.15 0.10 0.10 0.05 0.05 0 0 50 100 150 200 250 300 350 400 450 500 0 0 50 100 150 200 250 300 350 400 450 500 Flow rate l/min(ANR) Flow rate l/min(ANR) Pressure characteristics

Inlet pressure: 0.5 MPa Inlet pressure: 0.5 MPa Inlet pressure: 0.5 MPa 100 01, 23, 03, 04, 06, 07 01, 23, 03, 04, 06, 07 AS-F 06, 07, 08, 09, 10 500 08, 09, 10, 11 Flow rate L/min (ANR) Flow rate L/min (ANR) Flow rate L/min (ANR) 03, 04 TMH 400 200 06, 07 02 01, 23 ASD 300 50 03, 04 100 200 AS 01, 23 100 AS-FE 0 0 0 KE 5 0 10 5 0 10 5 0 10 Number of needle rotations Number of needle rotations

The standard output pressur for moving part air logic is 50 PSIG (3.44 Bar). The 25 PSIG pllot pr$sure required to shlft this valve gives approximately th samo response lo shitl and to return when the pllot pressure applled is 50 PSIG (3.44 Bar). The minimum volume of iho pilol chamber and the small swept volume disptaced by the short.slroke apool also aid in tast response.