PFxx-OMU0002 Do not use the product in the presence of a magnetic field. Malfunction can result. Do not let foreign matter, such as wire debris, get inside the product. Otherwise it can cause damage or malfunction. Do not use the product in an environment that is exposed to temperature cycle.
Do not use in an atmosphere having corrosive gases, chemicals, sea water, water, water steam, or where there is direct contact with any of these. 2. Do not use in explosive atmospheres. 3. Do not use in locations subject to vibration or impact. 4. Do not use in locations where radiated heat will be received from nearby heat sources. 5.
12 stations F 1 to 12 Manifold is 12 stations max.
Do not touch the span calibration trimmer except when performing span calibration. Touching the trimmer may cause generation of an error in the measured pressure. Also do not turn it too hard (0.3 Nm or less) or press it too hard (5 N or less). 7. Use a soft cloth to wipe the blot off of the body.
Do not touch the span calibration trimmer except when performing span calibration. Touching the trimmer may cause generation of an error in the measured pressure. Also do not turn it too hard (0.3 Nm or less) or press it too hard (5 N or less). 7. Use a soft cloth to wipe the blot off of the body.
4 6.8 55.3 8.5 13.9 7 52.3 45.3 7 9 3 M10 x 1.0 14 4 8.7 62.3 10 16.2 12 79.1 67.1 8 12 5 M14 x 1.5 19 6 12 92.6 13.5 21.9 15 88.2 73.2 10 17 6 M20 x 1.5 27 6 18 105.2 17 31.2 25 124 99 12 24 8 M27 x 1.5 36 6 25 147 23 41.6 The dimensions of H/L type are the same.
Do not mount the product in locations where it is exposed to radiant heat. 5. Do not use in dusty locations or where water, oil, etc., splash on the equipment. 6.
KPGR08-12 12 d 10 18.5 24 41 29 50.5 25.7 9 KPQR10-12 KPGR10-12 Note 1) D indicates the maximum diameter.
KPGR08-12 12 d 10 18.5 24 41 29 50.5 25.7 9 KPQR10-12 KPGR10-12 Note 1) D indicates the maximum diameter.
To install/remove the product, use an appropriate wrench to tighten/loosen at the supplied nut on body B. 12. Mounting Do not apply torque at other points as the product may be damaged. Rotate body A manually for positioning after installation. Warning 1.
ring Flange Hexagon socket head cap screw Piston rod y Except 12, 16 Except 12, 16 Bumper Ring nut Scraper pressure Rubber magnet u i o !
Safety Instructions Warning Do not disassemble, modify (including changing the printed circuit board) or repair. An injury or failure can result. Do not operate the product outside of the specifications. Do not use for flammable or harmful fluids. Fire, malfunction, or damage to the product can result. Verify the specifications before use.
Do not apply excessive lateral load to the piston rod.
Do not disassemble the cables. Use only specified cables. 3. Do not connect or disconnect the wires, cables and connectors when the power is turned on. Caution 1. Wiring securely. Do not apply any voltage to the terminals other than those specified in the Operation Manual. 2. Wire the connector securely. 3. Take appropriate measures against noise.
Do not Do not operate the product outside of the specifications. Do not use the product with flammable or harmful fluids. Fire, malfunction, or damage to the product may result. Check the specifications before use. Do not Do not use in an atmosphere containing flammable or explosive gases. Fire or an explosion may result. This product is not explosion-protected.
Do not use in atmospheres where the valve is in direct contact with corrosive gases, chemicals, salt water, water or steam. 2. Do not use in an explosive atmosphere. 3. Do not use in locations subject to vibration or impact. Confirm the specifications in the main section of the catalog. 4. Use a protective cover, etc., to shield valves from direct sunlight. 5.
Wiring of control signal input part 12 6-4. Wiring of output part 12 6-5. Wiring of RS-232C 12 6-6. Noise countermeasures 13 Chapter 7: Setting and Counter operation 7-1. Modes and setting items 14 7-1-1. Mode types and functions 14 7-1-2. Mode switching procedure 14 7-1-3. Setting of function mode 15 7-1-4. Data setting range 16 7-2. Setting 17 7-3. Counter operation 21 7-3-1.
Do not use until you can verify that equipment can operate properly. Verify correct mounting by suitable function and leakage inspections after air and power are connected following mounting, maintenance or conversions. 2. Do not drop or bump. Do not drop, bump or apply excessive impact (1000 m/s2) when handling.
Do not drop or bump. Do not drop, bump or apply excessive impacts (1000m/s or more for solid state switches) while handling. Although the body of the switch may not be damaged, the inside of the switch could be damaged and cause a malfunction. 2. Do not carry a cylinder by the auto switch lead wires. Never carry a cylinder by its lead wires.