MHS 1) CR MHSHJ3-J40 MHSHJ3-J50 MHSHJ3-J63 MHSHJ3-J80 19 1) FKM MHSHJ3-J40F MHSHJ3-J50F MHSHJ3-J63F MHSHJ3-J80F (A) 1) Si MHSHJ3-J40S MHSHJ3-J50S MHSHJ3-J63S MHSHJ3-J80J 1CRFKMSi 2131415161718 1 25 MHSH3DA MHSH3-A A 1 P 2 P 3 4 5 P 6 7 8 C 9 10 NBR 11 NBR 12 NBR 13 NBR MHSH3-A32A MHSH3-A40A MHSH3-A50A MHSH3-A63A MHSH3-A80A NBR MHSH32A-PS MHSH40A-PS MHSH50A-PS MHSH63A-PS MHSH80A-PS
A trunnion cannot be attached to a cover with a lock installed. Lock Specifications 2. Locking type manual override While pressing the M/O knob, turn it 90 counter clockwise. When the mark on the cap is aligned with the OFF mark on the M/O knob, the lock will be released (the lock will remain in a released condition).
Do not use a screwdriver with a large grip or with a tip that does not fit into the trimmer groove because this could strip the groove. Refer to pages 16-14-3 to 16-14-4 for Safety Instructions and Common Precautions on the products mentioned in this catalog, and refer to pages 16-111 to 16-1-13 for Precautions on every series.
A low valve closing speed relieves the water hammer. Operation < Valve opened > When the coil u is energized the opened pilot A closes, the pressure in the pressure action chamber B rises and the main valve C closes. < Valve closed > When the coil u is not energized, the closed pilot valve A opens, the pressure in the pressure action chamber B drops and the main valve C opens.
A Section A-A Bolt holder (movable) Approx. 0.5 or less 849 Dual Rod Cylinder/Compact Type CXSJ 2122CXSJ/ 1112Dimensions: 6 Air Preparation Equipment Pressure Control Equipment Flow Control Equipment Pressure Switches/ Pressure Sensors Directional Control Valves Air Grippers Modular F. R.
Auto Switch Proper Mounting Position (Detection at Stroke End) D-A9 D-M9 22 (24.5) A 2.8 0.5 W B ( ): Dimensions for D-A93 Bore size (mm) D-A9 A B W 6 10 16 36 11.5 9.5 (7) D-M9 A B W 29.5 5.5 3.5 (1) 29.5 9.5 7.5 (5) 33.5 9.5 0.5 33.5 13.5 3.5 40 15.5 5.5 20 41 15 13 (10.5) 45 19 9 25 40.5 16.5 14.5 (12) 45.5 20.5 10.5 Note) The above mentioned values are indicated as a guide for auto switch
Auto switches marked with a "" symbol are produced upon receipt of order. Note 1) Take note of hysteresis with 2 color indication type switches.
Note 3) For wear ring A of 10, please consult with SMC. 111 Magnetically Coupled Rodless Cylinder/Direct Mount Type: Centralized Piping Type Series CY3R 6, 10, 15, 20 25, 32, 40, 50 63 Replacement Procedure is P.316 Construction Centralized piping type CY3RG10 @9 @6 @4 @5 #0 @8 @7 CY3RG15 to 63 @4 @9 @6 #0 @5 @8 @7 The numbers are the same as the "Construction" of the Best Pneumatics No.2
Vacuum pressure switches There will be no change in performance if a pressure of approximately 0.5 MPa is applied momentarily (when releasing vacuum), but care should be taken that pressures of 0.2 MPa or more are not applied on a regular basis. Operating Environment Warning 1.
Whether designed in a manifold or used as a single valve, this small profile increases design flexibility and minimizes space requirements. The SYJ valve utilizes a low power (0.5 watts standard) pilot solenoid design, which dramatically reduces thermal heat generation. This improves performance, decreases operating costs, and allows for direct control by PLC output relays.
Whether designed in a manifold or used as a single valve, this small profile increases design flexibility and minimizes space requirements. The SYJ valve utilizes a low power (0.5 watts standard) pilot solenoid design, which dramatically reduces thermal heat generation. This improves performance, decreases operating costs, and allows for direct control by PLC output relays.
Whether designed in a manifold or used as a single valve, this small profile increases design flexibility and minimizes space requirements. The SYJ valve utilizes a low power (0.5 watts standard) pilot solenoid design, which dramatically reduces thermal heat generation. This improves performance, decreases operating costs, and allows for direct control by PLC output relays.
The tensile strength of the power cord is 49N, and pulling it with a greater force can cause failure. Warning 1. Vacuum pressure switches There will be no change in performance if a pressure of approximately 0.5MPa is applied momentarily (when releasing vacuum), but care should be taken that pressures of 0.2MPa or more are not applied on a regular basis. Operating Environment 3.
PORT SOLENOID VALVE, VVD, 111 lb
Whether designed in a manifold or used as a single valve, this small profile increases design flexibility and minimizes space requirements. The SYJ valve utilizes a low power (0.5 watts standard) pilot solenoid design, which dramatically reduces thermal heat generation. This improves performance, decreases operating costs, and allows for direct control by PLC output relays.
Whether designed in a manifold or used as a single valve, this small profile increases design flexibility and minimizes space requirements. The SYJ valve utilizes a low power (0.5 watts standard) pilot solenoid design, which dramatically reduces thermal heat generation. This improves performance, decreases operating costs, and allows for direct control by PLC output relays.
Whether designed in a manifold or used as a single valve, this small profile increases design flexibility and minimizes space requirements. The SYJ valve utilizes a low power (0.5 watts standard) pilot solenoid design, which dramatically reduces thermal heat generation. This improves performance, decreases operating costs, and allows for direct control by PLC output relays.
Whether designed in a manifold or used as a single valve, this small profile increases design flexibility and minimizes space requirements. The SYJ valve utilizes a low power (0.5 watts standard) pilot solenoid design, which dramatically reduces thermal heat generation. This improves performance, decreases operating costs, and allows for direct control by PLC output relays.
Whether designed in a manifold or used as a single valve, this small profile increases design flexibility and minimizes space requirements. The SYJ valve utilizes a low power (0.5 watts standard) pilot solenoid design, which dramatically reduces thermal heat generation. This improves performance, decreases operating costs, and allows for direct control by PLC output relays.
Whether designed in a manifold or used as a single valve, this small profile increases design flexibility and minimizes space requirements. The SYJ valve utilizes a low power (0.5 watts standard) pilot solenoid design, which dramatically reduces thermal heat generation. This improves performance, decreases operating costs, and allows for direct control by PLC output relays.