High Precision Digital Pressure Switch, Series ZSE50F/ZSE60F, ISE50/ISE60 Initial setting mode 2. OUT1 output mode selection 3. OUT2 output mode selection SET Press the SET button. Press the SET button at least 2 seconds.
SY SYJ 0 VQ4 0 1 Plug-in SX 2 5 VQ4 1 Plug lead VK VZ Enclosure Configuration Dust-proof 2 position single 3 position closed center VF (A) 4 (B) 2 (A) 4 (B) 2 Dust tight, jet proof (Applicable to IP 65) W 3 1 VFR 1 (P) 5 (R1) 3 (R2) 1 (P) 5 (R1) 3 (R2) Manual override 2 position double 3 position exhaust center (A) 4 (B) 2 (A) 4 (B) 2 VP7 Metal Rubber B: Locking slotted style : Non-locking
8 3 position Pressure center 1.2 1/8 Note) ( ): Normal position 5-3-23 6 Series VFRA4000 Dimensions 03 04 2 position single: VFRA411103 04 2 position double: VFRA4211(Pilot port) (Pilot port) Main valve manual override (Direct manual) Main valve manual override (Direct manual) 2-6.5 (Mounting hole) (Pilot port) (Mounting hole) (Pilot port) Courtesy of Steven Engineering, Inc.-230 Ryan Way
4) 4) , , , , 1)-10-20 2) 1) 1) 1) 1) 50mm 2/s 2) 2) 2) 2) 3) 3) 3) 3) 4) 5), 6) 4 SGC200*-OMJ0004-A SGC/SGH Series SGC/SGH Series SGC/SGH Series SGC/SGH Series 2 2 2 2 / / / / Nm Rc1/8 79 Rc1/4 1214 Rc3/8 2224 Rc1/2 2830 Rc3/4 4550 Rc1 6570 , , , , 1.5~2 1) 2) 3) 2 5 SGC200*-OMJ0004-A SGC/SGH Series SGC/SGH Series SGC/SGH Series SGC/SGH Series 2 2 2 2 / / / / 30 1 1) 2)1 0.1MPa
N.O. 1/8 to 3/4 2 to 10
Connecting Female Thread: G Approx. spanner tightening angle after tightened by hand deg Standard torque (Nm) Nominal size of uni thread 1 8 1 4 3 8 1 2 30 to 45 15 to 30 15 to 30 15 to 30 3 to 4 4 to 5 8 to 9 14 to 15 2. Gasket can be recycled 6 to 10 times. It can be replaced easily when it has sustained damage.
Start up procedure / Connecting to a computer . 5 2. 1 Preparation . 5 (1) Confirmation of product . 5 (2) Wiring . 5 (3) Installation of the Card Motor . 6 (4) Prepared and wired by the user. . 7 (5) Software installation . 7 2. 2 Controller settings . 8 (1) Start the setup software . 8 (2) Basic Parameter Setup . 9 (3) Step data setting . 9 3Start up procedureTest operation using a computer
Note 2) Refer to Construction of each series for the construction numbers.
Be sure to change the detecting position in the state of step 2. When auto switch is set on the mounting side as shown below, allow at least 2 mm runoff space on mounting plate since the auto switch is protruded from the gripper edge. Runoff space 2 mm or more Mounting bracket , Note) Use a watchmaker s screwdriver with a grip diameter of 5 to 6 mm to tighten the set screws (M2.5).
-Outside Local Area: (800) 258-9200-www.stevenengineering.com 32 40 14 Pilot EXH. 2-5.5 Mounting hole 2-1/4 3 1 Manual override (Non-locking) 9 23 VFN212N--02-D 213 19 23 Applicable heavy-duty cord O.D.6 to 8 Pg9 24 66.5 57 32 40 14 2-5.5 Mounting hole Pilot EXH. 177 2-1/4 3 1 9 23 Manual override (Non-locking) 4-17-2 3 NAMUR Interface 3 Port Solenoid Valve Series VFN200N NAMUR Mounting Pattern
2 4 Can be used for 110V and 115VAC, 220V and 230VAC in common.
operating pressure 250 PSI/1.7 MPa Minimum operating pressure 8 PSI/0.06 MPa Ambient and fluid temperature 40 to 140F / 5 to 60 C Piston speed 2 to 30 in/sec (50 to 750 mm/sec) Lubrication Not required (Pre-lubricated at Factory) Mounting B, C, E Standard Stroke (inch) Mounting Max. stroke as standard Long stroke Standard stroke 1/2, 1, 2, 3, 4, 5, 6 1/2, 1, 2, 3, 4, 5, 6 1/2, 1, 2, 3, 4
VR VH VHS Construction VHS20/30 VHS40/40-06/50 6 8 7 2 2 5 5 1 4 IN OUT OUT IN 1 9 3 EXH. EXH. Component Parts No.
This software is to be used in accordance with this Agreement non-exclusively for the limited purpose of writing data to the controller for SMC electric actuators. 2. This software can be installed and saved on a PC for the sole purpose specified in the preceding paragraph. Article 2 (Restrictions) 1. This software is not to be copied except as specified in Article 1-2. 2.
2 !3 !4 !5 !6 q w e r t y u i Block packing !
No. 2 2 1 DIN DIN DIN DIN 1 1) X 1/8 2)X 1.PE 2.X PE 3.
2 !3 !4 !5 !6 !7 !8 Nickel plated * * * * Replacement Parts: Seal Kits Bore (mm) Contents Kit No. 32 40 50 63 80 100 MBQ32-PS MBQ40-PS MBQ50-PS MBQ63-PS MBQ80-PS MBQ100-PS Set of the No. !3, !4, !5, and !
Reversed output 2ot : [ 2_P] Normal output Display Pressure setting EPL : [ 25] kPa EPH: [ 50] kPa OUT2 setting F 2 2 Tie rod holes SUP port Hysteresis EH : [ 5] kPa SET button Response time rES : [ 1000] Connector pin No. (Body side) Connector pin No. (Cable side) F 6 Display value compensation Sub screen [ 0.0] Compensated value: 0.0 Connector pin No.