Mechanically jointed rodless cylinder Basic short type (Rubber bumper), Basic standard type (Air cushion) Slide bearing guide type (Air cushion) Daily Check 1) Smoothness of the operation 2) Changes in piston speed and cycle time 3) Smooth movement of the slide table for the entire stroke 3-1-2.
Compatible cable Cord O.D.: 3.5 to 7 (Reference) 0.5 , 2-core, or 3-core, equivalent to JIS C 3306 When using other than SMC brand tube, confirm that the following specifications are satisfied with respect to the tube outside diameter tolerance.
Note 1) 2 1/8, 1/4 3 3/8 4 1/2 Type Metric size Inch size 2 Elbow 3 Universal Tubing O.D. 01 1/8" 03 5/32" 07 1/4" 09 5/16" 11 3/8" 13 1/2" Tubing O.D. 23 3.2 Note 2) 04 4 06 6 08 8 10 10 12 12 16 16 Control type 0 Meter-out 1 Meter-in * Meter-out and meter-in types can be visually identified by color of the knob.
X, Y, Z directions, for 2 hours each 2% F.S.
Possible causes Countermeasures 2 Air leaks from the One-touch fitting. 2-1) Tube is not inserted all the way into the fitting. 2-2) Tube has a gouge 2-3) The cut surface of the tube is slanted. Check all possible causes and make sure the piping is correct. Replace the part, if necessary. 2-4) One-touch fitting seal is damaged Replace One-touch fitting assembly 3.
H 4 S y m b o l Initial power/ Power 100 VAC 600/150 800/220 1200/350 200 VAC 2400/150 3200/220 4800/350 consumption (W) Heater assembly number XLA25-60S-2 XLA25-60S-2 XLA25-60S-2 No. of heater assemblies 2 pcs. 3 pcs. 4 pcs.
(Pilot port 2 opens) The valve leaves from the body seat to open by applying pressure to the pilot port 2. (Open pilot port 1) 2. Bypass valve The valve leaves from the body seat to open up to the set value by applying pressure to the pilot port 3. The valve returns to the original position by releasing air pressure of the pilot port 3. 5-2.
Daily Check 1) Smoothness of the operation 2) Changes in piston speed and cycle time 3) Smooth movement of the slide table for the entire stroke 3-1-2.
2 !2 Gasket O-ring NBR, Stainless steel NBR !3 !3 O-ring Retaining ring for hole type C Tool steel NBR !4 !4 Spacer Note) 10, 12, 3/8", 1/2" are made of POM, stainless steel, and brass (Electroless nickel plated). POM (2) !5 Gasket NBR, Stainless steel !6 Retaining ring for hole type C Tool steel !
External release: Directly released by external 2 port valve. Table (3) Vacuum Switch/ Lead Wire with Connector ZL Table (2) Valve Unit/Valve Plug Connector Assembly Connector assembly part no.
OPEBATION ACTUATOR 315 DSi used pruggeo 1/2 Solit D c pruggeo used 1/2 Solit B 3-15 osi c USEO plugged '1l2 Solit B 3-15 nsi pruggeo used '112 Solit D Fig. Reverse = ) Y INSTALLATION STYLE (REF. FrG. 1) QW tP3100 METHOD OF OPERATION Signal pressure trom a controlled pressure source enters the lP3l00 positioner through the signal port.
32 H L CBQ2 Standard A93 S B 50 D C CDBQ2 With Auto Switch 32 H L Number of auto switches With auto switch (built-in magnet) 2 pcs. 1 pc.
If Terminal no.1 a small flat head screwdriver is inserted into the gap between housing (2) and terminal block (3), terminal block (3) will be removed from housing (2). (See diagram at the top right of the page.) Coil Terminal no.2 4) Remove cable gland (4), washer (5) rubber seal (6).
Outer dimensions and descriptions of each part 4Outer dimensions and descriptions of each part 1) Outer dimensions HAW2/7 HAW22 to 110 2VHAW110-30 Flange (mm) Model A B C D E F G H J K L M N P Q R S T U V W Y Z ZA HAW2-04 360 190 83 35 270 35 130 203 159 159 182 209 60 60 94 4.5 10 1/2 1/2 1/2 HAW7-06 570 390 83 35 480 35 130 203 159 159 182 209 60 60 94 4.5 10 3/4 1/2 1/2 HAW22-14 948 575
Remove the excess sealant. c) Insufficient tightening may cause seal failure, or loosen the threads. d) Reuse 1. Normally, fittings with a sealant can be reused 2 to 3 times. 2. To prevent air leakage through the sealant, remove any loose sealant stuck to the fitting by blowing air over the threaded portion. 3.
Inch' size I0 1/4" 03/8' 05/16" 05/16" diameter . . 03/S' 051160 1/2" Flbw."rate tlin\~ 330 750 350 C ,oP/rolled flow . (A,MR~~N '(lmjQ' . 180 600 1100 1190 [Ereo flaw) Effettive ~IOnal 11.6 17 2.9 5.2 18.4 5.4 9.3 'ttrea mm 2 . N01e} The iMicaled 110w rate values are al a pressure 01 O.5MPa and a temperature 01 20 Q C. 1 Speed Controller 5 .
P 1= 0.7 MPa/P 2=0.5MPa PB 31 31 24 Although A, B+ and B marks are indicated on the terminal 55 Effective area at exhaust side(mm 2) AEA block, VFR4000 can be used as either +COM or COM. 45 S at P 2 = 0.5 MPa BEB solenoid valve.
02 Symbol 0 2 3 5 6 P Applicable tubing O.D.
Wiring Current A Terminal block Connection 3 is not used for terminal 1 and 2. Note) Coil has no polarity. Pin plug shape Applicable cable (Cabtire cable) 0.75 mm2, 1.25 mm2/2 core, 3 core (O.D. 6.8 to 11.5) based on JIS C 3312 and C 3322. Outlet changing procedure To change the wire outlet, first separate the terminal cover from the terminal block.